Dek-265GSX-User-Manual.pdf.pdf - 第114页

Parameter Definition Stencil Protection This parameter sets whether tooling to support the stencil, outside the board and clamp envelopes, is in use. Options are: Not Fitted; Fitted Default Fitted NOTE This parameter is …

100%1 / 388
Parameter Definition
Forward Y offset Programmable offset of the print on the board when printing from the rear. A
positive offset moves the print to the rear of the board.
Minimum -1.0mm
Maximum +1.0mm
Increment 0.004mm
Forward θ offset
Programmable offset of the print on the board when printing from the rear. A
positive offset moves the print in a clockwise direction.
Minimum -1000 arc seconds
Maximum +1000 arc seconds
Increment 2 arc seconds
Reverse X offset Programmable offset of the print on the board when printing from the front.
A positive offset moves the print to the right of the board.
Minimum -1.0mm
Maximum +1.0mm
Increment 0.004mm
Reverse Y offset Programmable offset of the print on the board when printing from the front.
A positive offset moves the print to the rear of the board.
Minimum -1.0mm
Maximum +1.0mm
Increment 0.004mm
Reverse θ offset
Programmable offset of the print on the board when printing from the front.
A positive offset moves the print in a clockwise direction.
Minimum -1000 arc seconds
Maximum +1000 arc seconds
Increment 2 arc seconds
Print Mode This parameter sets the mode of operation of the machine. Available modes
are:
PRINT/PRINT, PRINT/FLOOD, FLOOD/PRINT, ADHESIVE.
The default is PRINT/PRINT.
Selecting Adhesive from this parameter opens the separation delay and print
vacuum mode.
Front Print Speed This parameter sets the speed across the screen when printing.
Minimum 2mm/sec
Maximum 150mm/sec
Increments 1mm/sec
Default 10mm/sec
Rear Print Speed This parameter sets the speed across the screen when printing.
Minimum 2mm/sec
Maximum 150mm/sec
Increments 1mm/sec
Default 10mm/sec
Front Pressure This parameter sets the force applied by the front squeegee during its print
stroke.
Minimum 0kg
Maximum 20Kg
Increments 0.2Kg
Knead Off-image This parameter sets whether ProFlow is to knead in an off-image area of the
stencil. Options are:
Enabled; Disabled
Default Enabled
Knead Before Printing This parameter sets ProFlow to knead before printing the first board and the
amount of boards to be printed between kneading.
Minimum 0 (disables knead before printing)
Maximum 100
Increment 1
Default 0
NOTE
This parameter is only displayed, if knead off-image is set to enabled.
Software Version 6 User Manual 1.97
MACHINE PROGRAMMING
MENU PARAMETERS
Parameter Definition
Stencil Protection This parameter sets whether tooling to support the stencil, outside the board
and clamp envelopes, is in use. Options are:
Not Fitted; Fitted
Default Fitted
NOTE
This parameter is only displayed while ProFlow is fitted.
Rear Pressure This parameter sets the force applied by the rear squeegee during its print
stroke.
Minimum 0kg
Maximum 20Kg
Increments 0.2Kg
Print Gap This parameter sets the gap required between the screen and board to be
printed during the print stroke.
Minimum 0mm
Maximum 6mm
Increments 0.025mm
Separation Speed This parameter sets the speed at which the first 3mm of separation of board
and screen occurs.
Minimum 0.1mm/sec
Maximum 20mm/sec
Increments 0.1mm/sec
Separation Distance This parameter sets the separation distance between board and screen. The
parameter can help increase cycle time when a low separation speed is used
by decreasing the separation distance.
Minimum 0.0mm
Maximum 3.0mm
Increments 0.1mm
Default 3.0mm
Separation Delay This parameter is the time in seconds that the table delays before lowering.
This delay occurs during screen cleaning and after the flood. This parameter
only becomes available when Adhesive has been selected in the Print Mode
parameter.
Print Deposits This parameter sets the number of consecutive print strokes carried out on
one substrate.
Select 1, 2 or 3
Default 1
ProFlow Cassette This parameter sets the size of the transfer head used by the ProFlow unit.
Size may be one of the following:
300mm
400mm
500mm
NOTE
For 350mm and 450mm transfer heads, set to 400mm and 500mm
respectively.
ProFlow System Pressure This is the amount of print pressure (downward force) applied onto the stencil
by the ProFlow unit.
Maximum 20Kg
Minimum 0kg
Increments 0.2Kg
Default 0
ProFlow Paste Pressure This is the pressure applied to paste in the ProFlow unit while kneading and
printing.
Maximum 4 bar
Minimum 0.2 bar
Increments 0.2 bar
Default 2 bar
NOTE
This parameter is only available if the software controlled regulator is fitted.
1.98 User Manual Software Version 6
MACHINE PROGRAMMING
MENU PARAMETERS
Parameter Definition
ProFlow Idle Pressure This is the pressure applied to paste in the ProFlow unit between kneading
and printing, and between print strokes.
Maximum 4 bar
Minimum 0 bar
Increments 0.2 bar
Default 0.4 bar
NOTE
This parameter is only available if the software controlled regulator is fitted.
Flood Speed This parameter sets the flood blade speed across the screen when performing
a flood stroke.
Minimum 10mm/sec
Maximum 150mm/sec
Increments 1mm/sec
Flood Height This parameter sets the height of the flood blade above the screen during a
flood stroke.
Minimum 0mm
Maximum 5mm
Increments 0.02mm
Dwell Height The parameter allows the user to set the squeegee dwell height. Setting of a
lower height helps the media to stay evenly spread across the length of the
squeegee when a less viscous media is used. Setting a high height allows
viewing of the paste roll.
Minimum 5mm
Maximum 40mm
Increment 1mm
Default 30mm
Dwell Speed This preference adjusts the speed at which the squeegee moves to dwell
height. A slower speed helps to reduce the spreading of a less viscous media,
ie flux. It should be noted that decreasing this speed causes the cycle time to
increase.
Minimum 10mm/sec
Maximum 30mm/sec
Increment 1mm/sec
Default 24mm/sec
Screen Clean Mode 1
(Including Vacuum)
This parameter sets the mode of operation of the screen cleaner for the first
clean mode. When selected this parameter opens a window that allows a
screen clean option sequence to be chosen. The sequence includes six stages,
each of which may be one of the following cleaning operations:
WET, DRY, VAC, NONE
A warning is given if the end stroke is wet.
Screen Clean Rate 1 This parameter sets the number of print cycles between the cycling of the
screen cleaner for the first screen clean rate.
Minimum 0 (Screen cleaner off)
Maximum 200
Increment 1
Screen Clean Mode 2
(Including Vacuum)
This parameter sets the mode of operation of the screen cleaner for the second
clean mode. When selected this parameter opens a window that allows a
screen clean option sequence to be chosen. The sequence includes six stages,
each of which may be one of the following cleaning operations:
WET, DRY, VAC, NONE
A warning is given if the end stroke is wet.
Clean Screen Rate 2 This parameter sets the number of print cycles between the cycling of the
screen cleaner for the second screen clean rate.
Minimum 0 (Screen cleaner off)
Maximum 200
Increment 1
Print Vacuum mode This parameter determines the state of the vacuum during the print and flood
stages of the cycle. The parameter is only available if Adhesive has been
selected in the Print Mode parameter.
ON, OFF
Software Version 6 User Manual 1.99
MACHINE PROGRAMMING
MENU PARAMETERS