N5194A矢量适配器数据表.pdf - 第2页

Page 2 Find us at www .keysight.com Defin itions an d Cond itions Specification (spec): re prese nts warra nted per for manc e of a calibr at e d instru ment that h as be en stored for a m inimum of 2 ho urs wi thin the …

DATA SHEET

N5194A and N5192A

UXG Agile Vector Adapter 50 MHz to 40 GHz

Page 2

Find us at www.keysight.com

Definitions and Conditions

Specification (spec): represents warranted performance of a calibrated instrument that has

been stored for a minimum of 2 hours within the operating temperature range of 0 to 50°C, unless

otherwise stated, and after a 1 hour warm–up period. The specifications include measurement

uncertainty. Data represented in this document are specifications unless otherwise noted.

Typical (typ): describes additional product performance information that is not covered by the

product warranty. It is performance beyond specifications that 80% of the units exhibit with a

95% confidence level at room temperature (approximately 25°C). Typical performance does not

include measurement uncertainty.

Nominal (nom): describes the expected mean or average performance, or an attribute whose

performance is by design, such as the 50 Ω connector. This data is not warranted and is

measured at room temperature (approximately 25°C).

Measured (meas): describes an attribute measured during the design phase for purposes

of communicating expected performance, such as amplitude drift vs. time. This data is not

warranted and is measured at room temperature (approximately 25°C).

All of the above apply when using the instrument in its default settings unless otherwise stated.

This data sheet provides a summary of the key performance parameters for UXG vector adapters.

All options referenced in this data sheet are described in the UXG vector adapter configuration

guide (5992–2332EN).

This is a combined data sheet for the N5194A UXG Vector Adapter and the N5192A

UXG

Vector Adapter, Modified version. Unless otherwise stated, all specifications, typical, nominal and

measured values described in this data sheet will be the same for the N5194A and N5192A and

apply:

– When the N5194A UXG vector adapter is used together with the N5193A UXG agile signal

generator with options EP1 enhanced phase noise, FR1 fine frequency resolution, SS2/SS4

switching speed, and CC1 LVDS I/O interface.

Note:

– The minimum options required for proper operation are SS2/SS4 switching speed and

the CC1 LVDS I/O interface.

– The N5194A UXG agile vector adapter 40 GHz model (option 540) only requires a 20 GHz

N5193A UXG agile signal generator to operate over its full 40 GHz frequency range.

– When the N5192A UXG vector adapter is used together with the N5191A UXG agile signal

generator with options FR1 fine frequency resolutions, SS3 switching speed and CC1 LVDS

I/O interface.

Note: The minimum options required for proper operation are SS3 switching speed and the

CC1 LVDS I/O interface.

The N5193A and N5191A provide the 6 GHz reference and LO signals necessary for operating the

N5194A and N5192A respectively.

1. Unless otherwise noted, this data sheet applies to units with serial numbers ending with xx6006xxxx or greater.

2. Because of the high-performance characteristics of the N5194A, a U.S. export license is required. The N5192A

is a modified version of the UXG agile vector adapter that provides high performance without requiring an

export license. Notable differences include maximum available frequency and switching speed.

Page 3

Find us at www.keysight.com

Specifications

Frequency

Range

Specified range Tunable range

N5194A with option 520 50 MHz to 20 GHz 10 MHz to 20 GHz

N5194A with option 540 50 MHz to 40 GHz 10 MHz to 44 GHz

N5192A with option 52E 50 MHz to 20 GHz 10 MHz to 20 GHz

CW frequency resolution

0.001 Hz

Phase offset

Adjustable in 0.1° increments

Accuracy

Accuracy is equivalent to the external frequency reference in use.

External 6 GHz reference input

Frequency 6 GHz

Input amplitude +5 to +15 dBm (nom)

Input impedance 50 Ω (nom)

Lower band 10 MHz to < 20.000000016 GHz

– Main lower band 50 MHz to < 20.000000016 GHz

– Extended lower band 10 MHz to < 50 MHz

Upper band 20.000000016 GHz to 44 GHz

– Main upper band 20.000000016 GHz to < 40 GHz

– Extended upper band 40 GHz to 44 GHz

1. RF CW switching speed using an external hardware trigger. Speeds apply for any combination of frequency, amplitude ≤ max specified power and phase

switching.

2. For indexed waveform mode and real-time pulse generation mode during PDW streaming operation, minimum pulse spacing is 240 ns. Certain frequency

transitions will result in longer spacing due to update rate (transition time) limitations as described on Page 3 and 4. Also refer to page 9 under “PDW

streaming” for more details.

Switching speed for N5194A

1,2

Lower band Upper band

Main lower band Main upper band

40 GHz

20.000000016 GHz

44 GHz

10 MHz 50 MHz

Extended upper bandExtended lower band