TK26620.Feeder Maintenance Notice.pdf - 第2页

 SMT Software Engineering Group  IM Operations Y AMAHA MOTOR CO., L TD   MDOC-SOFT50282  2/17  1. Model and V ersion Supported models and version are as follows. T able1 . Model and V ersion Model ･ Software V ers…

100%1 / 17
SMT Software Engineering Group
IM Operations YAMAHA MOTOR CO., LTD
MDOC-SOFT50282
1/17
Feeder Maintenance Notice Operation Manual
Contents
Feeder Maintenance Notice Operation Manual.............................................................................................1
Contents..............................................................................................................................................................................1
1. Model and Version....................................................................................................................................................2
2. Introduction...................................................................................................................................................................2
2.1 Feeding Count....................................................................................................................................................2
2.2 Feeder MACS correction value..................................................................................................................4
2.3 Pickup error rate................................................................................................................................................4
3. Details of function.....................................................................................................................................................5
3.1 Message.................................................................................................................................................................5
3.2 Notification on the Feeder ID Log screen.............................................................................................9
3.3 Production Monitor screen..........................................................................................................................10
4. Setting Method.........................................................................................................................................................11
4.1 Software Setting...............................................................................................................................................11
4.2 Machine Setting................................................................................................................................................13
5. Limitation.....................................................................................................................................................................17
Rev Version Chapter
Revised Contents
00 V3.42STD R1.000
V4.42STD R1.000
- Created
01 V3.43STD R1.000
V4.45STD R1.000
1 - 4 Maintenance Stop Function added
02 V3.45STD R1.000
V4.48STD R1.000
1 - 5 Maintenance conditions added
・Feeder MACS Correct
・Pickup Error Rate
本文書に含まれる技術内容は当社の秘密情報です。当社の許諾無く第三者への開示はできません。
The information contained in this message may be confidential and legally protected under
applicable law. The message is intended solely for the addressee(s).
If you are not the intended recipient, you are hereby notified that any use, forwarding,
dissemination, or reproduction of this message is strictly prohibited and maybe unlawful.
SMT Software Engineering Group
IM Operations YAMAHA MOTOR CO., LTD
MDOC-SOFT50282
2/17
1. Model and Version
Supported models and version are as follows.
Table1. Model and Version
Model･Software Version Remarks
YS Series Mounter V3.42STD R1.000 or later SS feeder and ZS feeder only
YSM40, YSM20 V4.45STD R1.000 or later 〃
SS Tune-up Station V3.42STD R1.000 or later
2. Introduction
To keep accuracy of SS feeder and ZS feeder (hereafter, “feeder”), it is recommended to
have periodic maintenance.
This function can find factors that may cause increase of pick-up error rate, and notifies
the time of maintenance.
2.1 Feeding Count
After use of feeders over a specific number of times, the accuracy of tape feeding can be
reduced. Therefore, it is recommended to adjust the feeding position periodically.
When there is a feeder that has been driven a specific number of times since the last
maintenance, a message is displayed to notify that it is the time of maintenance.
Adjustment of feeding position is available on SS Tune-up Station. If you don’t have SS
Tune-up Station, please send the feeder to YAMAHA or distributor. （Refer to Fig 2.1）
After the feeder is maintained on SS Tune-up Station, the maintenance message is no
longer displayed, and it will be displayed again when the feeding count comes to the
specific count again.
SMT Software Engineering Group
IM Operations YAMAHA MOTOR CO., LTD
MDOC-SOFT50282
3/17
【with SS Tune-up Station】
【without SS Tune-up Station】
Fig 2.1 Maintenance work image
MaintainthefeederonSSTune-upStation
MaintenanceNoticeappears
Notice・ErrorOccurrence
Feeder
SSTune-upStation
MaintenanceNoticedisappears
Notice・ErrorResolution
Mounter
MaintenanceNoticeappears
Notice・ErrorOccurrence
Feeder
Mounter
SendthefeedertoYamahao/distributor
Yamahamaintainsthefeeder
MaintenanceNoticedisappears
Notice・ErrorResolution
SSTune
-
upStation
Yamaha/distributorsendsthefeederback