Select-Coat-SC-104-105-NordsonASYMTEK.pdf - 第2页
Page 2 of 3 S elect Coat ® SC -1 04/10 5 Film Co ater Specifications Film patte rn width: 6.35 to 1 9.05 mm (0.25 to 0.75 in.) Masking required: n o Material viscosity: under 100 cP s Application thic kness : Solvent - b…
Page 1 of 3
Select Coat
®
SC-104/105 Film Coater
Precise Non-Atomized Conformal Coating Application
The Prime SC-104/105 Film Coater Fluid System
optimizes throughput and increases yield by
delivering high velocity, excellent edge definition,
and the ability to program and use a variety of
coating widths.
The non-atomized film coater is compatible with a
circulating fluid system, and provides automated,
selective application of conformal coating materials
with viscosities less than 100 centipoise.
Programmable applicator modes – spots, lines, and
area coverage – provide powerful coating results
that fit your specific process needs. Consistent fan
pattern – even after idle – is ensured by the unique
design that circulates heated fluid through the
applicator extension maintaining a consistent nozzle
temperature at all times.
Easy Coat
®
software creates process synergy
between the applicator and platform design through
routines and validation steps that can be used to
define the optimal start and stop points during
production.
Programmers define the process temperature and
the corresponding process limits in Easy Coat
software. If the fluid temperature moves outside the
defined process limits during production, the
system triggers an alarm condition and operators
can intervene to prevent potential errors.
To optimize the Prime SC-104/105 Film Coater
Fluid System, you have the choice of two nozzles
and two fluid reservoirs of either 1- or 5-gallon
capacity. Fluid pressure is controlled electronically
through Easy Coat software
– ensuring optimal
performance to match your production needs.
The SC-104/105 Film Coater Applicators are
intended for use with the Select Coat
®
SL-940
conformal coating system.
Features and Benefits
High coating velocity up to 750 mm/sec
With a transfer efficiency of virtually 100 percent, the
Film Coater applicator improves conformal coating
utilization by 30 to 50 percent
The non-atomized design minimizes common
problems such as over-spray, masking, and rework
Wet coating thicknesses range from 125 to 750 µm
(0.5 to 3 mils) for solvent-based materials and 0.1 to
0.2 mm (4 to 8 mils) for 100-percent solid materials
A heated, circulating fluid system provides closed-
loop temperature control and allows fluid viscosities
to remain independent of the ambient environment
The standard Fourth Axis provides a 0 – 90 degree
rotation of the fan pattern
Optional Fifth-Axis Tilt accessory increases
accessibility to tight or difficult-to-access areas that
may not be achievable with the standard downward
approach (0 degrees)
SC-104 Heated, Circulating
Film Coater
Page 2 of 3
Select Coat
®
SC-104/105 Film Coater Specifications
Film pattern width: 6.35 to 19.05 mm (0.25 to 0.75 in.)
Masking required: no
Material viscosity: under 100 cPs
Application thickness:
Solvent-based materials: 0.50 to 3 mils
100-percent solids materials: 4 to 8 mils
Edge tolerance: ± .762 mm (± 0.03 in.)
Transfer efficiency: over 99%
Coating velocity: 130 to 510 mm/sec (5 to 20 in./sec)
Typical fluid dispense pressure: 103 to 413 kPa (15 to 60 psi)
Pattern width: 6.35 to 19.05 mm (0.25 to 0.75 in.)
Featured Options
Fifth-Axis Tilt
Laser Fan Width Control
Dual-Simultaneous Programmable Pitch
SC-105 Heated, Circulating Film
Coater with optional Fifth-Axis
Tilt
Page 3 of 3
Select Coat
®
SC-104/105 Film Coater
Fifth-Axis Tilt – Additional Benefits
Fifth-axis tilt allows the film coater nozzle to be rotated and tilted to access hard-to-
reach areas of the product. Programmers can easily set and modify the rotate and tilt
parameters for an applicator within Easy Coat
®
software.
• Ideal for coating vertical surfaces and underneath components
• The nozzle can tilt at 30 degrees, and the mechanism can be rotated in 4
positions – in 90-degree increments (0, 90, 180, and 270) to direct the fan
pattern to the left, right, front or back to coat all four sides of a component
• The nozzle is fully integrated into the applicator assembly and can be installed
horizontally for a narrow coating pass when it is tilted or vertically to achieve
vertical area coverage
• Tilting of the nozzle as opposed to tilting the entire applicator eliminates the
need for a direct line of sight and provides optimal agility during the
conformal coating process
Dual Simultaneous – Additional Benefits
With the dual-simultaneous configuration, the SL-940 system can coat two parts
(multiple-up) at the same time. Processing two parts in parallel significantly improves
the throughput, while maintaining high yield. The actual conformal coating process
time is reduced by 50%, so that throughput performance can be significantly increased
– especially when conducting a high takt time conformal coating process with few
overhead movements.
Two of the same applicators are installed and operate simultaneously. When there is
no need for simultaneous conformal coating, Easy Coat software allows the
programmer to disable the second applicator and set the pitch as part of the
programming.
• Coat two parts at once – reducing overall cycle time
• Enable the second applicator as needed
• Fully adjustable pitch
Dual-Simultaneous Programmable Pitch
Nordson ASYMTEK
+1.760.431.1919
2747 Loker Avenue West
Carlsbad, CA USA 92010-6603
Published 2018-03-21 (Updated)
For more information,
visit our website to
locate your local
representative or
contact your regional
office:
nordsonasymtek.com
info@nordsonasymtek.com
North America
Headquarters
Carlsbad, CA
China
Shanghai
Beijing
Guangzhou
Taipei
EMEA
Deurne, Netherlands
S.E. Asia/Australia
Singapore
Korea
Seoul
Japan
Tokyo
India
Chennai