Scope_of_Service_Delivery_Specific_Part_E By DEK_eV28.pdf - 第5页

ASM AS GmbH & Co KG SMT Placement Systems Version 2. 8 Scope of Servi ce and De livery E B Y DEK Page 5 of 5 Release: 01. 09 . 201 9 Editor: ASM AS PM , RGO S cope_of_Se rvice_Del ivery_S pecific_Par t_E B y DEK_eV 2…

ASM AS GmbH & Co KG SMT Placement Systems Version 2.8

Scope of Service and Delivery E BY DEK Page 3 of 5 Release: 01.09.2019

Editor: ASM AS PM, RGO

Scope_of_Service_Delivery_Specific_Part_E By DEK_eV28.docx

3 Standards and guidelines

3.2 Service standards during product lifecycle

ASM AS provides a general warranty regarding the equipment capabilities as mentioned in the plat-

form independent document “Scope of Service and Delivery – Common part”.

The customer must comply with the preventative maintenance schedule as specified in the Tech-

nical Reference Manual/Maintenance manual supplied with the equipment Failure to do so will

have a direct effect on the capability of the machine to perform within the specifications and will

affect the warranty on the equipment. Any equipment with a warranty period greater than 1 year,

must receive its annual service each year by an ASM AS qualified engineer. The timing of this ser-

vice will be determined by the anniversary of the Warranty Start Date

The warranty period commences 2 weeks from the date of shipment.

Period of Standard Warranty

Labour 15 months

Parts 15 months

ASM AS GmbH & Co KG SMT Placement Systems Version 2.8

Scope of Service and Delivery E BY DEK Page 4 of 5 Release: 01.09.2019

Editor: ASM AS PM, RGO

Scope_of_Service_Delivery_Specific_Part_E By DEK_eV28.docx

8 Technical Availability

8.1.6 Maintenance Time (Refer to Technical reference / Maintenance Manual)

This variable includes all maintenance time including:

• Scheduled daily maintenance – 15 minutes per day/shift

• Scheduled monthly maintenance – 2 hours per month

ASM AS GmbH & Co KG SMT Placement Systems Version 2.8

Scope of Service and Delivery E BY DEK Page 5 of 5 Release: 01.09.2019

Editor: ASM AS PM, RGO

Scope_of_Service_Delivery_Specific_Part_E By DEK_eV28.docx

11 Standard Acceptance Criteria

11.3 Printer Installation and Customer Acceptance

This section details the printer capability test carried out during a machine installation and cus-

tomer acceptance. (refer to installation manual)

11.3.1 Printer Capability Test

The printer is set up with the following menu parameters for the following test using an ASM align-

ment board (provided with machine):

• Product File – 265test1

• Stencil – Calibration/Dry Align (provided with machine)

• Squeegee – 250mm

• Front & Rear Print Speed – 25mm/sec

• Front & Rear Pressure – 5kg

• Separation Speed – 1mm/sec

• Under Board Clearance – 20mm

• Paste Dispense – 0

• Under Stencil Rate – 0

• Transport Mode – Left to Left

Use nine magnetic tooling pins to fully support the board and apply a small amount of paste or lub-

ricant (enough to lubricate squeegees). Ensure the onboard SPC program set up correctly to rec-

ord and report the relevant axes.

11.3.2 Printer Alignment Capability

The printer alignment capability is detailed below

• Machine Alignment Capability - > @ +/- 12.5µm

• System Alignment Capability - > 2.0 Cmk @ +/- 25µm, (±6 Sigma)

11.3.3 Printer Core Cycle Time

The printer core cycle time capability is detailed below

Core Cycle Time – 11.0 secs*

Measured using the ASM defined Core Cycle Time test parameters, for details contact the Product Manager