00195334-01.pdf - 第17页
HS-50 transport contr oller 2 Retrofit instructions internal C onveyor control TSP200 in machine no .: 1-20 SIPLACE HS-50 08/2000 Edition 17 2.4 Part s The part s needed for the retrofi t are: 2 2 2 2 2 2 2 2 2 2 2 2 Ite…
2 Retrofit instructions internal Conveyor control TSP200 in machine no.: 1-20 SIPLACE HS-50 HS-50 transport controller
08/2000 Edition
16
2.3 Safety instructions
WARNING
The safety instructions from the "Operational safety" chapter of the user manual and servicing in-
structions take precedence over these instructions. 2
The SIPLACE placement machines are supplied with main power voltage.
Consequently parts of these systems carry dangerous voltages! This voltage is present at certain
modules inside the machine base, even when the machine is switched off at the main power
switch.
Incorrect handling of the placement machine or touching live parts of the machine can result in
death or severe injury, and considerable damage to equipment.
BEFORE starting any work, shut down the operating system correctly, then switch the machine
OFF at the main power switch and disconnect from the main power supply. In addition, the com-
pressed air supply must be switched off at the compressed air unit's main valve in the machine
base and vented by actuating the needle valve on the compressed air unit.
There is DANGER for heart pacemaker wearers in the vicinity of the linear motors, as described
in detail in the "Special safety instructions for working in the vicinity of strong magnetic fields"
section of the user manual and service manual.
Always follow the accident prevention regulations, DIN or other standards and special safety
rules applicable in your country.
Pay attention to the information concerning residual voltages in the Operational Safety chapter.
Follow the ESD regulations as described in the operational safety section of the operating
instructions.
During the retrofit, always secure the machine to prevent access by other people and to prevent
it being switched on again. The procedure is described in the “Locking the machine…” section of
the user manual.
Working with the SITEST program further increases the risk of accident.
The SITEST program must only be used by authorized and trained personnel.
2
2.3.1 Definitions
2
Please note 2
2
HS-50 transport controller 2 Retrofit instructions internal Conveyor control TSP200 in machine no.: 1-20 SIPLACE HS-50
08/2000 Edition
17
2.4 Parts
The parts needed for the retrofit are: 2
2
2
2
2
2
2
2
2
2
2
2
Item number Quantity
Either
retrofit kit TSP200 dual conveyor 00349886S02 1
or
retrofit kit TSP200 single conveyor 00349885S02 1
Spacer bolt M4x8 a/a 00353452-01 4(8*)
Spacer bolt M4x35 i/i 00353742-01 4(8)
Fillister head screw M4x8 00845024-01 4(8)
Plain washer 4(8)
Hexagon socket head screw M5x10 00845042-01 1
Cover for conversion board, left 00351962-01 1
Cover for conversion board, right 00351961-01 1**
Motor cable M7 conveyor 1 00351931-01 1
Motor cable M7 conveyor 2 00353230-01 1
Sensor cable M6 conveyor 1 00351932-01 1
Sensor cable M6 conveyor 2 00353231-01 1
Sensor cable M5 conveyor 1 1
Sensor cable M5 conveyor 2 1
Small parts 2 adhesive tabs /cable ties
Retrofit instructions: conversion kit for controller TSP200
D+E 00192267-01 1
Retrofit instructions: Old - New special design 1
2 Retrofit instructions internal Conveyor control TSP200 in machine no.: 1-20 SIPLACE HS-50 HS-50 transport controller
08/2000 Edition
18
2.5 Preparatory work
: Remove the component trolleys (ideally on both sides on the dual conveyor).
: Switch the placement system off at the main switch.
: Remove the nozzle changers and tape cutters.
: Remove the attachment on the input side (if possible, in order to pull in the cables).
: Remove the covers from sector 1 and 4.
: Open up the retrofit version of the TSP200.
Detach the ribbon cables and the conversion boards.
2
Fig. 2.5 - 1 Complete retrofit kit
2