5OM-1286-007_w.pdf - 第16页
Safety Precautions Safe-5 AJQE-ID 0606-005 In principle, the overall operation of the machine including the button operations on the operation panel and the touch screen must be controlled by only one person. If there …
Safety Precautions
Safe-4
AJQE-ID
Precautions before Use
Confirm that no covers are disengaged before operating the machine.
If the machine is used with its cover(s) being detached, a serious accident may
occur.
Be sure to attach them in place.
Make certain that no person or object comes in contact with the moving
mechanisms of the machine. Then, check safety and power up the machine to
start operation.
Do not start the machine unless those working in the immediate area of the
machine are aware of hazards from moving parts.
Those who wear implanted pacemakers are not allowed to work inside the
machine.
This machine uses strong permanent magnets in the moving areas of the X/Y
beams.
The pacemaker may be affected by the magnetism and a serious accident will
result.
Those who wear implanted pacemakers are not allowed to handle the tape
feeders.
The pacemaker may be affected by the magnetism and a serious accident will
result.
If the bank feeder change cart is not set, a clearance will be left at the feeder
setting area and the operator will be exposed to danger.
B
e
sure to use the machine with the bank feeder change cart being connected.
Even after the [EMERGENCY STOP] switch is pressed, note that electrical
power is supplied to the control device.
T
o shutdown the power to all loads, set the power breaker to "OFF".
W
hen "Emergency Switch Off" is required, it must be prepared outside the machine on
the customer side.
Emergency Switch Stop :
Emergency Interception of Controlled Load Power
Sources
Emergency Switch Off
: Emergency Interception of All Load Power Sources
0606-005
Safety Precautions
Safe-5
AJQE-ID
0606-005
In principle, the overall operation of the machine including the button
operations on the operation panel and the touch screen must be controlled by
only one person.
If there are more than one, ensure good communication by giving loud verbal
instructions.
Before starting the automatic operation, check carefully that there is no person around
the machine (especially on the other side of the machine operation). Make sure that no
objects (tools, parts, etc.) are left behind.
Data may become unavailable due to breakdown or mishandling of the machine.
It is strongly recommended that the hard disk data be periodically backed up with the
network terminal (option).
Do not use the floppy disk drive in the control box.
The drive is provided only for the
authorized maintenance personnel.
Safety Precautions
Safe-6
AJQE-ID
Notes on Machine Operations
This machine uses energetic driving systems and high voltage to run at high
speed. This power and voltage is high enough to cause death or serious injury.
To avoid this danger
, respect the following guideline.
• The machine must be used with the covers being attached.
• Be sure to close the covers (door type) before operating the machine.
• Do not disengage the interlock mechanism of the covers (door type).
Whenever you feel danger or abnormality, immediately press the
[EMERGENCY ST
OP] switch to stop the machine.
If the machine is kept running in abnormal condition, an accident or a
breakdown will result.
Confirm that the "LOCK" lamp (green) is ON on the operation panel before
operating the machine.
If the "LOCK" lamp is not turned ON, the machine can be operated at any time
from both front and rear sides, endangering the operators around the machine.
When there is a problem with the machine, locate the cause and assess the
condition. Set the power breaker to "OFF".
After the problem has been rectified completely
, reset the machine to its
normal condition.
When the green lamp of the light tower is ON or flickering (ON and OFF), it indicates
that the static machine is in the "Automatic" mode (standby mode).
In case of a disaster of any kind, earthquake, storm, flood, fire, or lightning,
immediately stop the machine and turn off the power supply
.
When the machine stops due to a component pickup error
, be sure to remove the
mispicked component from the feeder and start the automatic operation.
Do not use any unspecified feeders.
0606-005