Infinity Generic Tooling.pdf - 第2页

INFINITY MACHI NE PROG RAMMI NG STAGE 6 A - M AGNET IC PILL ARS TOO LING 1.28 User Manual 6. Select Save (F2). The message ‘Saving fiduci al data - Please wait Board dat a file saved’ i s display ed. 7. Select Exit (F8).…

100%1 / 52
INFINITY
MACHINE PROGRAMMING
STAGE 6A - MAGNETIC PILLARS TOOLING
User Manual 1.27
STAGE 6A - MAGNETIC PILLARS TOOLING
WARNING
BOARD CLAMPS. EXTREME CARE MUST BE EXERCISED WHEN WORKING IN
THE TOOLING AREA OF THE MACHINE TO AVOID INJURY. THE FOILS ON THE
FRONT AND REAR BOARD CLAMPS ARE VERY SHARP.
CAUTION
BOARD CLAMPS.
Care must be taken to ensure that the board clamps are
not damaged when removing or replacing tooling.
NOTE
Ensure that Generic Tooling is set to Enabled in Set Prefs.
1. Select Change Tooling (F6). The print carriage moves to the front of the
printer.
The Change Tooling Parameters window is displayed:
NOTE
If the remote board stop is fitted the Board Stop X and Board Stop Y
parameters are replaced by Remote Board Stop X.
2. Setting up the board stop position is automatically done using the board
dimensions previously set in the product file. If they need adjustment to re-
position the board stop for any reason, ie any routing on the board edge or
a badly positioned image on the stencil, this can be done now. If adjustment
is necessary continue with Step 3. If adjustment is not necessary go to Step
8.
3. Select Adjust (F1).
4. Use the Next and Previous keys (F4 - F5) to highlight each parameter.
5. Use the Incr. and Decr. keys (F6 - F7), or the forward slash key (/) on the
keyboard, to change the parameter value.
Mode
Load
Data
Edit
Data
Setup
Squeegee
Change
Screen
Change
Tooling
Change
Language
Exit
Change Tooling Parameters
BOARD WIDTH
BOARD STOP X
BOARD STOP Y
UNDER CLEARANCE
216.0
125.0
142.6
19.0
mm
mm
mm
mm
Adjust
Raise
Head
Remove
Cleaner
Board
Stop
Full
Width
Load
Width
Generic
Tooling
Exit
Save Next Previous Incr. Decr. Exit
Save Next Previous Incr. Decr. Exit
INFINITY
MACHINE PROGRAMMING
STAGE 6A - MAGNETIC PILLARS TOOLING
1.28 User Manual
6. Select Save (F2). The message ‘Saving fiducial data - Please wait Board
data file saved’ is displayed.
7. Select Exit (F8).
8. Select Generic Tooling (F7).
The following window and menu bar is displayed:
NOTE
If contaminated squeegees are fitted, these should be replaced at this point.
9. Select Continue (F1). The print carriage travels to the rear of the machine
and the following message is displayed ‘Table at Home Height’.
10. Select Transprt Height (F3). The message ‘Table at Transport Height’ is
displayed.
11. Place a board on the input sensor of the upline conveyor of the machine.
12. Select Load (F1).
13. Select Auto Board (F1).
Save Next Previous Incr. Decr. Exit
Save Next Previous Incr. Decr. Exit
Adjust
Raise
Head
Remove
Cleaner
Board
Stop
Full
Width
Load
Width
Generic
Tooling
Exit
Generic Tooling Warning
WARNING Paste may drip into the machine
Remove Squeegees NOW
Continue
Open
Cover
Exit
Continue
Open
Cover
Exit
Load
Transprt
Height
Board
Clamps
Change
Screen
Raise
Head
Exit
Load
Vision
Height
Home
Height
Board
Clamps
Change
Screen
Raise
Head
Exit
Auto
Board
Manual
Board
Exit
INFINITY
MACHINE PROGRAMMING
STAGE 6A - MAGNETIC PILLARS TOOLING
User Manual 1.29
14. Select Raise Head (F7).
15. Raise the printhead using two button control.
The following window and menu bar is displayed:
16. Fit the head prop.
17. Press Confirm (F1).
18. Position the outermost support pins on the rising table under the board.
Unload
Vision
Height
Home
Height
Board
Clamps
Change
Screen
Raise
Head
Exit
Hazardous Operation
The head must be propped while it is
raised
Insert the Head Prop.
Confirm
Lower
Head
Confirm
Lower
Head