manual-rhn-hand-support-for-phn-0027888_ID-215056.pdf - 第8页
Sliding Parts Maintenance - Che c k pe ri odi ca ll y that R HN i s cl ea n, es pe ci al ly th e sli di ng pa r ts a nd t he sh af t. - Us e a da mp c loth w he n cl ea ni ng. A lc oh ol ca n on ly b e use d to cl ea n t…
R
R
R
R
L
L
R
R
L
L
R
R
L
L
L
L
R
R
L
L
JTT
JTT
JTT
JTT
JTT
HRR and HRL can be combined with:
RWT Adjustable Rework Arm,
RWS Adjustable Rework Arm for PHSE and
RWB Adjustable Rework Arm for PHBE.
Assemble first the height adjustment flange (1), then the HRR (2) and afterward the HRL (3). Assemble
the second height adjustment flange (4) and finally the RWT (5).
Compatible JBC Articles*
* Not included, sold separately.
RWT
Ajustable Rework Arm
4 different sizes for PCB Supports are available:
- PHNS Support for PCBs up to 11x7 cm / 4x3”
- PHSS Support for PCBs up to 13x13 cm / 5x5”
- PHBS Support for PCBs up to 36x28 cm / 14x11”
- PHXLS Support for PCBs up to 51x61 cm / 20x24”
HRL
Articulated Left Hand Rest
HRR
Articulated Right Hand RestPlace the preheater set
in the area below the
hot air tool
Heights Adjustmet
Flange (1st)
Heights Adjustmet
Flange (2nd)
R
R
R
R
L
L
R
R
L
L
R
R
L
L
L
L
R
R
L
L
JTT
JTT
JTT
JTT
JTT
In the case of using both left and right arms, assemble both as shown in the illustration according to the
letters on the back of the hand rest, to keep the hand supports at the same level. The right hand rest
should be assembled below the left hand rest.
Accessories*
If a second hand rest ist needed, Articulated Left Hand Rest HRL is available. HRL also allows adjustment
for different positions.
HRL
Articulated Left Hand Rest
HRL
Articulated Left Hand Rest
HRR
Articulated Right Hand Rest
Bottom View
Mark for left hand
rest
Mark for right hand
rest
* Not included, sold separately.
Bottom View
7
40 mm
50 mm
60 mm
80 mm
100 mm
130 mm
130 mm
para manuales - color gris
200 mm
300 mm
Sliding Parts
Maintenance
- Check periodically that RHN is clean,
especially the sliding parts and the shaft.
- Use a damp cloth when cleaning. Alcohol
can only be used to clean the metal parts.
- Replace any defective damaged parts.
Use original JBC spare parts only.
Safety
- Do not use the equipment for any purpose other than PCB rework.
- The temperature of accessible surfaces may remain high after the unit is turned off. Handle with care.
- Be careful with the fumes produced when soldering.
- Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when
working to avoid personal harm.
- Do not leave up the arms directly above heat surfaces.
- Utmost care must be taken with liquid tin waste which can cause burns.
- This appliance can be used by children over the age of eight as well as persons with reduced physical,
sensory or mental capabilities or lacking experience provided that they have been given adequate
supervision or instruction concerning the use of the appliance and understand the hazards involved.
Children must not play with the appliance.
- Maintenance must not be carried out by children unless supervised.
It is imperative to follow safety guidelines to prevent electric shock, injury,
fire or explosions.
Shaft
Do not leave up HRR over the
preheater when the preheater
is working.
8
Notes
9
40 mm
50 mm
60 mm
80 mm
100 mm
130 mm
130 mm
para manuales - color gris
200 mm
300 mm