PSE_300_VS_TI_EN.pdf - 第4页

T echnical data T echnology base kolb PowerSpray ® Capacity per process cycle Screen, stencil, carrier , washing frame up to 950 x 780 mm (37.5 "x 31") Process chamber dimensions W 350 ▪ D 980 ▪ H 920 mm (W 13.…

Most suitable Optional suitable Not suitable Not suitableNot suitable

Cleaning / rinsing (key process 1): From the system tank a communicating cleaning and rinsing liquid is sucked by a

magnetically coupled pump unit and routed with a controllable volume flow into the ASYNCHRO

spray rotors with patented

PUSHFORCE

nozzles. Their geometry ensures a comprehensive and thorough cleaning, even in inaccessible and critical

aereas. The liquid is continuously filtered in circulation, so that the system progressively enters the rinsing process after

removing the contamination.

Drying (key process 2): The purified products are dried with the patented CWA

(Compressed Warm Air) technology. The

built-in special compressor compresses the ambient air. At the same time it collects the kinetic energy (frictional heat) of the

paddle wheel in the unit, then presses the heated and compressed air into the rotor nozzles which were already used for clea-

ning and rinsing. There it blows off (pressure) and evaporates (heat) the residual moisture. This method is energetically and

constructively highly efficient, as it uses the "waste heat" of the compressor rotation and the compressed air as driving power

for the rotors. In addition, a system equipped with CWA

technology requires no additional hardware and no external com-

pressed air connection for the MediumWipe

process.

Cycle time: < 18 min., depending on contamination and detergent

Maintenance: The system has a removable panel on the right side. In the maintenance area among others the pump-out set

is available. Tank levels as well as pressure values and maintenance cycles are monitored by the PLC. The tank level is also

easily controllable through a window in the system front.

Page 2 of 4

Part number: 0905PSE3VS-2

Fully automatic single chamber PowerSpray

-system with

2step process (cleaning / rinsing, drying)

11/2021

PSE 300 VS

Made in Germany

CLEANING TECHNOLOGY

kolb Cleaning Technology GmbH ▪ Karl-Arnold-Str.12 ▪ D - 47877 Willich ▪ Phone: +49 (0) 2154 9479 - 38 ▪ Fax: +49 (0) 2154 9479 - 47 ▪ e-mail: info@kolb-ct.com ▪ www.kolb-ct.com

Application overview

Solder frames

Solder carriers

Solder masks

ESD Boxes

Containers

Magazines

Condensation traps

Filters

Steel sheets

Optional suitable applications can also be optimally realized with the appropriate options.

Stencils

Screens, PumpPrints

Misprints (bare boards)

Assembled PCBs

Hybrids

Misprints (mounted)

All rights for changes reserved that lead to technical improvement. © kolb GmbH 2021

Main standard features

□ PowerSpray

technology bundle: magnetically coupled S-Power pump unit, twofold ASYNCHRO

volume-spray rotorsysterm

with PUSHFORCE

nozzles

□ Magnetic coupled pump unit

□ EATON Programmable Logic Controller (PLC)

□ High resolution 3.5" touch display

□ Full flow coarse filter (process chamber)

□ CWA

-supercharger compression drying

□ ClosedLoop reprocessing of cleaning and rinsing fluid

□ Safety features: safety interlock on the process chamber door, overheating protection for all heating and drying elements,

end switches for all motor-driven valves and drives, personnel protection insulation

□ Front cover made of stainless steel, side and rear covers in painted steel

□ Process sections made of electrolysis resistant elements

Main options

□ Cascaded filter system / Sediment filter for cleaning / rinsing tank

□ Drip & storage reservoir

□ Exhaust controil

□ Full stainless steel housing

□ Noise insulation

Page 3 of 4

Part number: 0905PSE3VS-2

Fully automatic single chamber PowerSpray

-system with

2step process (cleaning / rinsing, drying)

11/2021

PSE 300 VS

Made in Germany

CLEANING TECHNOLOGY

kolb Cleaning Technology GmbH ▪ Karl-Arnold-Str.12 ▪ D - 47877 Willich ▪ Phone: +49 (0) 2154 9479 - 38 ▪ Fax: +49 (0) 2154 9479 - 47 ▪ e-mail: info@kolb-ct.com ▪ www.kolb-ct.com

Technical data

Technology base kolb PowerSpray

Capacity per process cycle Screen, stencil, carrier, washing frame up to 950 x 780 mm (37.5 "x 31")

Process chamber dimensions W 350 ▪ D 980 ▪ H 920 mm (W 13.77" • D 38.85" • H 36.22")

Volume tank 75 - 100 l

Power supply 400 V AC, 16 A, CEE plug / 3 Ph / 50 or 60 Hz

Power consumption 3 kW

Control system PLC (Eaton E4 XV102)

Temperature load up to 50 °C (122 °F)

Filter system

up to three stages - 1. Full flow coarse filter < 2 mm (0.08"), 2. Sediment filter

inside the tank, 3. 20“ fine filter (1 - 100 µm - process dependent)

Exhaust connection Ø 160 mm (6.3"), exhaust capacity 200 - 300 m³ / h (7,063 - 10,595 ft³ / h)

Footprint 800 x 1,200 mm (31.49" x 47.24")

Operating condition room temperature 20 - 35 °C (68 - 95 °F)

Operating noise 75 dB (A)

Empty weight 330 kg (728 lbs)

Page 4 of 4

Part number: 0905PSE3VS-2

Fully automatic single chamber PowerSpray

-system with

2step process (cleaning / rinsing, drying)

11/2021

PSE 300 VS

Made in Germany

CLEANING TECHNOLOGY

kolb Cleaning Technology GmbH ▪ Karl-Arnold-Str.12 ▪ D - 47877 Willich ▪ Phone: +49 (0) 2154 9479 - 38 ▪ Fax: +49 (0) 2154 9479 - 47 ▪ e-mail: info@kolb-ct.com ▪ www.kolb-ct.com