ELA Installation.pdf - 第64页

FOREIGN MAC HINE INTERFAC E MULTI-INTERFACE UNIT 7.4 I nstallation M anual Chapter Issue 3 J un 01 Card Access T o gain access to the three selector switche s proceed as follo ws: 1. Remov e connections to the MIU. 2. Re…

100%1 / 90
FOREIGN MACHINE INTERFACE
MULTI-INTERFACE UNIT
Chapter Issue 3 Jun 01 Installation Manual 7.3
MULTI-INTERFACE UNIT
The DEK Multi-Interface Unit (MIU) is a communications interface that allows
DEK Printing Machines to communicate with upline and downline board han-
dlers.
It simplifies the set up of the communications link between machines of different
manufacture by providing preprogrammed and programmable connections to
suit the interface protocol types commonly found within the board processing
industry.
The onboard, switch selectable, interface types are detailed later in this section.
Up to 16 interfaces can be specified for upline and downline handlers. The
upline machine can be of a different interface type to the downline machine.
Power supplies of +24V, +12V, +5V and 0V power the communications devices
of the upline and downline machines. Input signals to the MIU are opto-isolated.
Relay or open collector output driver signals are available for the MIU outputs.
A patching area routes patching link connections direct from upline to downline
as specified by any given protocol requirement.
The RS232 link is used for carrying out self tests on the MIU only and has no
function on the ELA machine.
MIU Card Layout
Figure 7-3 MIU Card Layout
12345678
ON
0
8
2E
6A
C 4
0
8
2E
6A
C 4
ON
12345678
0
8
2E
6A
C 4
0
8
2E
6A
C 4
SW2 SW3
IC8
SW1
FS1 FS2 FS3
LD1
LD2
SW2 - Upline interface select switch
SW3 - Downline interface select switch
SW1 - RS232 function select switch
The setting of this switch is for carrying
out self tests on the MIU only and has
no affect on the ELA machine.
SW2 SW3
SW1
FOREIGN MACHINE INTERFACE
MULTI-INTERFACE UNIT
7.4 Installation Manual Chapter Issue 3 Jun 01
Card Access To gain access to the three selector switches proceed as follows:
1. Remove connections to the MIU.
2. Remove the MIU from the bracket by releasing the four screws.
3. Remove the six MIU back plate screws.
Part Numbers and Settings
NOTE
DEK do not supply Dynapert, Philips or Europlacer interface cables.
FMI Cables With the cables supplied, connect the upline and downline machines to the
screen printer MIU box connections. Cables should be routed down behind the
rear access panel.
Protocol
MIU Setting Cable Part Number
Upline SW2 Downline SW3 Upline Downline
Dynapert 0 0 N/A N/A
Philips 1 1 N/A N/A
SMEMA 2 2 131343 131345
Siemens 3 3 131335 131337
SMPI 4 4 131331 131333
TDK 5 5 131323 131325
Europlacer 6 6 N/A N/A
Fuji 7 7 126757 126758
Panasonic 7 7 131339 131341
Sanyo 8 8 146120 146119
Sanyo Flow Out 9 9 146120 146119
FOREIGN MACHINE INTERFACE
PROCEDURE
Chapter Issue 3 Jun 01 Installation Manual 7.5
PROCEDURE
Ensure MIU is configured with the correct protocols for upline and downline
machines as detailed earlier.
1. Power up the machine using the mains isolator, ensure that the air supply is
connected.
The message prompt bar displays - ‘Press SYSTEM Button To Initialize
Printer or Select Diagnostics or Load Data’.
2. Press System button, the machine initializes.
3. Select Maint. (F8).
4. Select Set Prefs,(F5).
The Set Preferences window is displayed.
5. Using the Next and Previous keys highlight the Upline Protocol function.
Use the Incr. and Decr. keys to change to the required protocol, eg. Sanyo.
6. Repeat Step 5 for the Downline Protocol. At this stage, if required, change
the Display Units, Transfer Mode etc.
Run
Open
Cover
Paste
Load
Clean
Screen
Adjust Setup Monitor Maint.
Calibrat
Pressure
Calibrat
Offset
Calibrat
Vision
House
Keeping
Set
Prefs
Diagnost
Test
Cycles
Exit
Set Preferences
TRANSPORT MODE
MACHINE UNITS
UPLINE PROTOCOL
DOWNLINE PROTOCOL
TRANSFER PERIOD
SELECTIVE PRINT/PASS
PASTE DISPENSE POS.
COMMS PROTOCOL
EVENT RECORDING
TOOLING HARDWARE
FIDUCIAL REFERENCE
PRESSURE H/W
SCREEN SIZE
CONSUMABLE ACTION
LEFT TO LEFT
Metric
NO FMI
NO FMI
20
DISABLED
FRONT
NO COMMS
GROUP 3
MAGNETIC
LEFT
FITTED
265
WARN
secs
..more
Next Previous Incr. Decr. Exit