00192375-01.pdf - 第230页

SIPLACE GEM for S25, HS50 SW Version GEM 502.01 HOST Inter face Manual Page 230 of 236 ©Siemens AG, all rights reserved Revol ver Head 3 CEID Nam e Descript ion 2310001 Plac e3Cycle Placement cycle com pleted on SP-head …

100%1 / 236
SIPLACE GEM for S25, HS50 SW Version GEM 502.01
HOST Interface Manual
©Siemens AG, all rights reserved page 229 of 236
CEID Name Description
2211004 FM_FM_SPURLEER Flatpack magazine is empty
2211005 FM_MHS_CRASH_GEFAHR Second gantry in travel range
2211006 FM_VAK_DELTA_GRENZE_SP RV: intervals open - closed vacuum
values too low
2211007 FM_VAK_OFFEN_GRENZE_SP RV: vacuum values for open nozzles
too high
2211008 FM_VAK_KUBISCH_SP RV: cubic vacuum values faulty
2211009 FM_VAK_NICHT_KUBISCH_SP RV: non-cubic vacuum values faulty
2211010 FM_VAK_FHL_NR_UNBEK_SP RV: unknown vacuum error number
2211011
FM_CAN_MSG_ABWERFEN_SP
RV: Defective motor for rejecting
2211012
FM_TW_SP_PINOLE_GEZOGEN
Caution: Sleeve in extended
position, do not move placement
head!
2211013 FM_VAK_SEGM_UNDICHT_SP Leak in RV-head segment after
placement
2211015 FM_BZ_SCHUETZ_SZ4 Software enable relay defective
2211016 FM_BZ_DRUCKTLUFT Compressed air failure for too long
2211017 FM_BZ_UNBEK_ZUST Status unknown
2211018 FM_BZ_SCHUTZ Cover not correct
2211019 FM_BZ_HALTEPUNKT Break point not defined
2211020 FM_BZ_SCHLUESSEL Unknown key-switch message
2211021 FM_BZ_SENDENBZ Unknown message code to BZ
2211022 FM_BZ_HAUPTSCHUETZ Hardware defect (relay)
2211023 FM_GUI_TEXT_BB_ERR_WAR
TE_ENDE_PORT_KPF_REF
Gantry and head reference run failed
2211024 FM_GUI_TEXT_BB_ERR_WAR
TE_ENDE_HOEHE_REF
Height reference run failed
2211025 FM_GUI_TEXT_BB_ERR_FAHR
E_POSITION
Unable to move gantry
2211027
FM_GUI_TEXT_TI_FOERD_FOLIE
Error upon cover foil of a tape feeder
2211028 FM_BETR_DATEN_NOK Error upon producing operating data
for a HOST system
2211029 FM_HEAD_TIMEOUT Timeout during head functions
2211031 FM_NOZZLE_NOK Nozzle cannot be changed, function
not executed
SIPLACE GEM for S25, HS50 SW Version GEM 502.01
HOST Interface Manual
Page 230 of 236 ©Siemens AG, all rights reserved
Revolver Head 3
CEID Name Description
2310001 Place3Cycle Placement cycle completed on SP-head 3 and
<PLACEINFOREV3> , <PLACEINFOREV3SUB1>
will be updated.
33
2310002 PickUp3Cycle Pick-up cycle completed on SP-head 3 and
<PICKUPINFOREV3> will be updated.
42
2310003 Nozzle3changed <NOZZLECONF3> changed on revolver head 3
(not in single function mode).
35
2310004 RefRunHead3 Head <HEIGHTREV3> reference run complete on
revolver head 3.
37
2310005 NozzleRefRun3 <NOZZLECONF3> length reference run complete
on revolver head 3.
35
2310006 VacRefRun3 <VAKUUMDATAREV3> reference run complete on
revolver head 3.
39
Revolver Head 4
CEID Name Description
2410001 Place4Cycle Placement cycle completed on SP-head 4 and
<PLACEINFOREV4>, <PLACEINFOREV4SUB1>
will be updated.
33
2410002 PickUp4Cycle Pick-up cycle completed on SP-head 4 and
<PICKUPINFOREV4> will be updated.
43
2410003 Nozzle4changed <NOZZLECONF4> changed on revolver head 4
(not in single function mode).
36
2410004 RefRunHead4 Head <HEIGHTREV4> reference run complete on
revolver head 4.
38
2410005 NozzleRefRun4 <NOZZLECONF4> length reference run complete
on revolver head 4.
36
2410006 VacRefRun4 <VAKUUMDATAREV4> reference run complete on
revolver head 4.
40
SIPLACE GEM for S25, HS50 SW Version GEM 502.01
HOST Interface Manual
©Siemens AG, all rights reserved page 231 of 236
 $ODUPV
There are no alarms defined for SIPLACE
$/,' $/&' $/7; 'HVFULSWLRQ 21&(,' 2))
&(,'
$/,' Alarm ID
$/&' Alarm Severity Code. The low-order 7-bits of ALCD specifies the severity
code. The high-order bit (bit-8) shows the current alarm state (1=SET,
0=CLEAR).
$/7; Alarm Text. This is the actual string sent the Host in the Alarm Report
(S5F1).
21&(,' This is the Collection Event that is signaled when the alarm state changes
from CLEAR to SET ("going-on").
2))&(,' This is the Collection Event that is signaled when the alarm state changes
from SET WRCLEAR ("going-off").