YSi-X_Ope_E.pdf - 第33页

General Contents Before using the machine 1. Using this manual i 1.1 A vailable manuals i 1.2 Manual contents i 2. W arranty ii 3. Contents of each chapter iii 4. Page layout iv Chapter 1 Par t names and functions 1. Mac…

100%1 / 124
xxix
Safety instructions
Warning/caution labels
Rear side
■ Lower panels
■ Laser unit inside machine
■ Panels inner side
■ Conveyor opening
■ Panels inner side
■ Side panel
93202-M6-00
General Contents
Before using the machine
1. Using this manual i
1.1 Available manuals i
1.2 Manual contents i
2. Warranty ii
3. Contents of each chapter iii
4. Page layout iv
Chapter 1 Part names and functions
1. Machine main unit 1-1
2.
Conveyor unit 1-5
3. Laser height sensor 1-6
4. Axis configuration 1-7
Chapter 2 Basic operation
1. Before operation 2-1
1.1 Canceling emergency stop 2-1
1.2 Clearing an error 2-1
2.
Starting and ending the machine and software operation
2-2
2.1 Starting 2-2
2.2 Ending 2-5
Chapter 3 Daily operation
1. Overview 3-1
2. Warm-up operation 3-2
3. Selecting the program 3-3
Chapter 4 Maintenance
Before beginning work 4-1
1. Maintaining machine performance 4-2
1.1 Essential conditions and working environment 4-2
1.2 Importance of periodic inspections and cleaning 4-2
EPM6172120
2. Maintenance list 4-3
3. Preparing for maintenance tasks 4-5
3.1 Consumable parts 4-5
3.2 Maintenance tools 4-6
3.2.1 Cleaning tools 4-6
3.2.2 Lubricating tools and grease 4-7
3.3 Required tools 4-8
3.4 Removing the rear center panel 4-9
4. Weekly inspection 4-10
4.1 Cleaning the camera lighting unit 4-10
4.2 Checking the board sensor condition 4-12
4.3 Checking the board clamp condition 4-12
5. Monthly 4-13
5.1 Inspecting each axis 4-13
5.2 Cleaning and greasing the ball screws and guides 4-14
5.2.1 Cleaning and greasing the XT-axis ball screws 4-14
5.2.2 Cleaning and lubricating the XT-axis guides 4-15
5.2.3 Cleaning and greasing the YT-axis ball screws 4-16
5.2.4 Cleaning and greasing the YT-axis guides 4-17
5.2.5 Cleaning and greasing the LX-axis ball screws 4-18
5.2.6 Cleaning and greasing the LX-axis guides 4-19
5.2.7 Cleaning and greasing the LY-axis ball screws 4-20
5.2.8 Cleaning and greasing the LY-axis guides 4-21
5.3 Inspecting and cleaning the conveyor belt 4-22
5.4 Checking the conveyor belt tension 4-24
5.5 X-ray generator 4-26
5.5.1 Inspecting the X-ray generator 4-26
6. Three-month inspection 4-28
6.1 Cleaning and greasing the ball screws and guides 4-28
6.1.1 Cleaning and greasing the W-axis ball screws 4-28
6.1.2 Cleaning and greasing the W-axis guides 4-29
6.1.3 Cleaning and greasing the MS-axis guides 4-30
6.2 Inspecting and cleaning the air filter 4-31
7. Six-month inspection 4-33
7.1 Cleaning and greasing the ball screws and guides 4-33
7.1.1 Cleaning and greasing the HZ-axis ball screws 4-33
7.1.2 Cleaning and greasing the HZ-axis guide 4-35
7.1.3 Cleaning and greasing the HS-axis ball screws 4-36
7.1.4 Cleaning and greasing the HS-axis guide 4-37
7.2 Cleaning the filter of controller (Type HD/Type HB) 4-38