Dek Training.pdf - 第3页

D e k P r i n t e r T r a i n i n g 3 / 7 0 2 5 J u n e 2 0 0 6

1. Machine Overview 机器概述

DEK 710

Stencil Size : 29” X 29”. If the stencil is not this size. Need to using Adapter.

钢网大小: 29 寸 X 29 寸.如果不是这大小要用钢网适配器

Camera: Cyber optic digital camera(Interface : IEEE1394 ,camera model is GREEN)相

机用 Cyber optic 数码相机(用 IEEE1394 连接, 相机型号 : GREEN)

2XCMOS 用二倍 CMOS 镜头

FOV=11.3 x 8.5 mm 每次可照大小是 11.3 x 8.5 mm

15 microns per pixel

Fiducial Size : 0.5mm - 3.0mm

Conveyor type : Front Fixed , L-L,R-R,L-R,R-L(If using Right to Left, it have right feed

delay time) 送板模式: 固定边在前面, 左进左出,右进右出,左进右出,右进左出(如果设

定是右进左出‧，会有一延迟时间设定)

PCB support : 81mm height 顶针是 81mm 高

Setup Machine Frame Leg : 36mm & 24 mm Spanner.机器脚的板手用 36mm 及 24mm

Voltage : 230V single phase(max 10A)230 伏单相电‧最大电流 10 安培

Weight :650kg 重量 650kg.

Table is fixed. Stencil can adjust.抬 XY 固定.只可上落Ｕ，

钢网可 XY 方向走动

Screen Offset Adjust

钢网走动

X,Y offset : +-3 degreeX & Y 正负三度

X have two offset motor (Fwd & rear) X 方向有两个马达

Y only have one offset motor. Y 方向有一个马达

Only 2 fiduical moark can setup. 只有二个 MARK(PCB 2 个,

钢网 2 个)

Board stop : Only mechnical stopper. 停板用机械气动顶住

One Board detect sensor 有一个看 PCB 的感应器

Board Handling ：

Minimum Size 40 x 50mm

Maximum Size 508 x 508mm

Thickness 0.2mm - 6mm

Maximum Weight 1Kg

Warpage Up to 8mm including PCB thickness

Underside Clearance Programmable 3mm - 42mm

Operating Envelope

Temperature 10 - 35°C (50 - 95°F)

Humidity 30 - 70% Relative Humidity (non condensing)

Approx. Weight 650kg

Approx. Dimensions 1314mm X 1608mm X 1825mm (Machine)

2. E-STOP Button & Signal Tower 紧急按纽及信号灯

Dek Printer Training 2/70 25 June 2006

Dek Printer Training 3/70 25 June 2006

3. PCB Clamping & System Switch 夹板刀和开机按纽

PCB clamping is very SHAPE(0.1mm Thickness). Please take care.

夹板刀十分锋利(0.1mm 厚)！请小心

4. Left & Right Toggle Button 左右两按纽控制

Left & Right Toggle Button are using in Diagnostic Mode.

左右两按纽控制在诊断模式用

5. Power up machine.开机的次序

3 Check Air Pressure. Normal is 0.5Bar – 0.6Bara. If Lower than 0.3Bar

will have pressure too low alarm.检查气压,正常在 0.5Bar 至 0.6 Bar.

如果少于 0.3 Bar 会有气压过低的报警机器开不了的

3 Measure the AC input power is within 230V +/- 10%. Power

Consumption Max 10A.检查电源在 230 伏正负百分之十内.最大电

流 10 安培

3 Release E-stop Button.放开紧急停止按纽

3 Turn on the Main Power Switch.At Machine Front Right Middle

Position. 打开总电开关在机器前面右中位置

3 Computer will automatic Turn on. 计算机会自动开机

Dek Printer Training 4/70 25 June 2006