oet_tds_117-167_StepLess_Ear_Clamps_EN.pdf - 第4页
F or alternatives, see Oetiker TDS of hand tools or power t ools 1 F urther information on ww w.oetiker .com 2 F or closing forces ≥ 7000 N, with the HO 7000, an inlet pressur e of > 5.5 bar is required. ! Important n…

3
StepLess
®
Ear Clamps Product Group 117 & 167
Note: the above sketch shows the appearance of a closed
“ear” (s’); it does not necessarily indicate an eective closed
assembly.
The following applies as a guideline: To determine the correct
clamp diameter, push the hose onto the attaching material,
(e.g. the nipple), and then measure the outer diameter of the
hose. The value of the outer diameter must be slightly above
the average value of the diameter range of the clamp to be
selected. A clamp can only be considered adequately closed
when the ear width (s) has been reduced by at least 40%, and
the correct closing force was used for assembly.
Block closure
Block closure means that, during the applied closing force,
both ear shanks of one ear clamp touch each other. The
closing force applied after the occurrence of block closure is
absorbed by the block closure and not transferred to the parts
being clamped. If a statement about the eective closing force
acting on the parts being clamped during closure is required,
a block closure should be avoided.
Mechanical interlock
The interlock is a mechanical system for joining the clamp
ends to permit closure. Some interlock designs can be
opened for radial installation prior to closure.
Assembly Recommendations
The clamp “ear” is deformed with a constant tool jaw force
– this practice is referred to as “force priority closure”. This
assembly method ensures that a uniform and repeatable
stress is applied to the joint in addition to a consistent tensile
force on the clamp interlock. Employing this methodology
when closing a 167 series clamp will compensate for any
component tolerance variations, and ensure that the clamp
applies a constant radial force to the application. Fluctuations
in component tolerances are absorbed by variations in the
“ear” gap (s’). Clamp installation monitoring and process data
collection are available by incorporating an “Electronically
Controlled Pneumatic Power Tool” Oetiker ELK in the
assembly process.
Closing force
The closing force must be chosen to give the required material
compression or surface pressure and should be qualified
by dimensional evaluation and experiment. The resistance
against the clamp equals the applied force, so the closing
force is greatly reduced when compressing a soft material.
The table below gives the maximum applied closing force
for clamp and material dimensions when compressing and
sealing relatively hard synthetic materials.
Complete process monitoring, including 100% documentation
is available using the Electronically controlled pneumatic
pincer ELK.
Rotation diameter
The rotation diameter (RD) of an assembled clamp can be
critical design information for applications that rotate in close
proximity to adjacent components. Many factors can influence
this final assembly diameter including compression, “ear”
gap “s” and material thickness. It is recommended that all
variables be considered and evaluated prior to specifying a
rotating diameter.
!
Important
– The ear height is naturally given. Do not influence the ear
height, either by changing the ear gap or with built-in hold-
down devices in installation tools.
– Single tool stroke closure only, do not apply secondary
crimping force.

For alternatives, see Oetiker TDS of hand tools or power tools
1
Further information on www.oetiker.com
2
For closing forces ≥ 7000 N, with the HO 7000, an inlet
pressure of > 5.5 bar is required.
!
Important note: These figures are intended as a guide,
they may vary depending on the type and tolerances of
parts being clamped. To ensure optimum clamp selec-
tion, we recommend making functional tests with several
assemblies.
4
StepLess
®
Ear Clamps Product Group 117 & 167
Material Size Closing Installation tools force-monitored
1
:
dimensions (mm) force max. Manual Pneumatic Cordless Electronically
(mm) (N) controlled
INSTALLATION DATA
PG 117
7.0 x 0.6 11.9 – 17.8 1100 HMK 01/S01 HO ME 2000 – 4000 CP 10 HO EL 2000 – 4000
PG 167
5.0 x 0.5 6.5 – 11.8 1000 HMK 01/S01 HO ME 2000 – 4000 CP 10 HO EL 2000 – 4000
5.0 x 0.6 18.5 – 100.0 1700 HMK 01/S01 HO ME 2000 – 4000 CP 10 HO EL 2000 – 4000
7.0 x 0.6 11.9 – 17.5 2100 HMK 01/S01 HO ME 2000 – 4000 CP 10 HO EL 2000 – 4000
17.8 – 120.5 2400 HMK 01 HO ME 3000 – 4000 CP 10 HO EL 3000 – 4000
7.0 x 0.8 17.7 – 120.5 2800 – HO ME 3000 – 4000 CP 10 HO EL 3000 – 4000
9.0 x 0.6 21.0 – 120.5 2800 – HO ME 3000 – 4000 CP 10 HO EL 3000 – 4000
9.0 x 0.8 25.0 – 120.5 4100 Clamping tool HO ME 5000 – 7000 CP 10 HO EL 5000 - 7000
and Torque wrench
10 x 0.6 21.0 – 120.5 2900 – HO ME 4000 – 7000 CP 10 HO EL 4000 – 7000
10 x 0.8 24.5 – 120.5 5000 Clamping tool HO ME 5000 – 7000 CP 20 HO EL 5000 – 7000
and Torque wrench
10 x 1.0 60.0 – 120.5 7000
2
Clamping tool HO ME 7000 CP 20 HO EL 7000
and Torque wrench
12 x 1.0 40.0 – 120.5 8500
2
Clamping tool HO ME 7000 CP 20 HO EL 7000
and Torque wrench

5
StepLess
®
Ear Clamps Product Group 117 & 167
ORDER INFORMATION PG 167
Item No. Ref. No. Ear width Size range
inside (mm) (mm)
Band width 5 mm, thickness 0.5 mm (505R)
16702488 006.5-505R 4 5.3 – 6.5
16700001 007.0-505R 4 5.8 – 7.0
16700002 008.0-505R 4 6.8 – 8.0
16700003 008.7-505R 5.5 7.0 – 8.7
16702491 009.0-505R 5.5 7.3 – 9.0
16700004 009.5-505R 5.5 7.8 – 9.5
16700005 010.0-505R 5.5 8.3 – 10
16700006 010.5-505R 5.5 8.8 – 10.5
16702492 010.9-505R 5.5 9.2 – 10.9
16700007 011.3-505R 5.5 9.6 – 11.3
16700008 011.8-505R 5.5 10.1 – 11.8
Band width 7 mm, thickness 0.6 mm (706R)
16702951 011.9-706R 8 9.4 – 11.9
16700009 012.3-706R 8 9.8 – 12.3
16702493 012.8-706R 8 10.3 – 12.8
16700010 013.3-706R 8 10.8 – 13.3
16700011 013.8-706R 8 11.3 – 13.8
16700012 014.0-706R 8 11.5 – 14
16702864 014.2-706R 8 11.7 – 14.2
16700013 014.5-706R 8 12 – 14.5
16700014 014.8-706R 8 12.3 – 14.8
16700015 015.3-706R 8 12.8 – 15.3
16700016 015.7-706R 8 13.2 – 15.7
16702998 016.0-706R 8 13.5 – 16
16702494 016.2-706R 8 13.7 – 16.2
16702495 016.6-706R 8 14.1 – 16.6
16702496 016.8-706R 8 14.3 – 16.8
16700017 017.0-706R 8 14.5 – 17
16702497 017.5-706R 8 15 – 17.5
16700018 017.8-706R 10 14.6 – 17.8
16700019 018.0-706R 10 14.8 – 18
16700020 018.5-706R 10 15.3 – 18.5
Item No. Ref. No. Ear width Size range
inside (mm) (mm)
Galvanized steel band
Band width 7 mm, thickness 0.6 mm (706)
11701202 011.9-706 8 9.4 – 11.9
11701081 012.3-706 8 9.8 – 12.3
11701100 012.8-706 8 10.3 – 12.8
11701061 013.3-706 8 10.8 – 13.3
11701101 013.8-706 8 11.3 – 13.8
11701102 014.0-706 8 11.5 – 14.0
11701108 014.5-706 8 12.0 – 14.5
11701062 014.8-706 8 12.3 – 14.8
11701109 015.3-706 8 12.8 – 15.3
11701063 015.7-706 8 13.2 – 15.7
11701103 016.2-706 8 13.7 – 16.2
11701119 016.6-706 8 14.1 – 16.6
11701110 016.8-706 8 14.3 – 16.8
11701064 017.0-706 8 14.5 – 17.0
11701065 017.5-706 8 15.0 – 17.5
ORDER INFORMATION PG 117
Zinc-plated steel band
Band width 7 mm, thickness 0.6 mm (706)
11700583 011.9-706 8 9.4 – 11.9
11700584 012.3-706 8 9.8 – 12.3
11700585 012.8-706 8 10.3 – 12.8
11700586 013.3-706 8 10.8 – 13.3
11700587 013.8-706 8 11.3 – 13.8
11700588 014.0-706 8 11.5 – 14.0
11700568 014.5-706 8 12.0 – 14.5
11700589 014.8-706 8 12.3 – 14.8
11700569 015.3-706 8 12.8 – 15.3
11700570 015.7-706 8 13.2 – 15.7
11700571 016.2-706 8 13.7 – 16.2
11700572 016.6-706 8 14.1 – 16.6
11700590 016.8-706 8 14.3 – 16.8
11700591 017.0-706 8 14.5 – 17.0
11700573 017.5-706 8 15.0 – 17.5