TDS_AirJet_594_CRD_SAC_ENG.pdf - 第3页

AirJet ® 594 CRD-SAC TECHNICAL DATA SHEET 3 www.dct.cleaning R D C C CLEANING RINSING DRYING R D Application name Recommended application Recommended temperature Total cleaning process time Capacity per 8 hours Re ow an…

100%1 / 8
AirJet
®
594 CRD-SAC 
TECHNICAL DATA SHEET
2
www.dct.cleaning
GENERAL INFORMATION
The AirJet
®
cleaning systems represent unique
air-bubbling technology developed and manufactured
by DCT.
Air-bubbling technology machines are developed
for gentle yet highly effi cient maintenance cleaning
of refl ow and wave soldering machines such
as soldering frames, fi lters, heat exchangers, etc.
The AirJet
®
can also be off ered for the removal
of conformal coatings. AirJet
®
cleaning systems are available
in several sizes and with diff erent levels of automation of the
cleaning process.
AirJet
®
594 CRD-SAC including 100% separated processes
of cleaning, rinsing and drying technologies.
All processes are automated and take place in 3 separate
process chambers, which are also storage tanks.
The AirJet
®
594 CRD-SAC is equipped with a motorized
manipulator for easy basket lowering, then pulling out the
baskets and moving them between the process chambers.
Thanks to this device, the operator is not forced to lift heavy
parts, making the machine extremely ergonomic, safe and
user-friendly.
Cleaning takes place in the  rst inlet chamber, where the
operator drops the parts basket using a manipulator.
After cleaning, the operator moves the basket to the rinsing
chamber and then to the drying chamber.
All 3 chambers can be used independently, which increases
the machine’s cleaning capacity and reduces cross-
contamination when compared with single-chamber devices.
Depending on your cleaning requirements,
the DCT project manager, in collaboration
with a local distributor, will advise you
on a suitable water-based cleaning fl uid
and the correct setup of the entire process.
AirJet
®
594 CRD-SAC 
TECHNICAL DATA SHEET
3
www.dct.cleaning
R
D
C
C
CLEANING
RINSING
DRYING
R
D
Application
name
Recommended
application
Recommended
temperature
Total cleaning
process time
Capacity
per 8 hours
Re ow and soldering parts
30 – 50°C 86 – 122 °F 35 min. 192 **
3 INDIVIDUAL PROCESSES
CLEANING PARAMETRES
highly recommended recommended applicable
* PCB eurocards / per 8 hours (calculated for dimension of 100 x 160 mm / 3.94 x 6.3 in)
* * Parts in soldering palette / per 8 hours (320 x 500 x 50 mm / 12,6 x 19,7 x 1,97 in)
* * * Stencils, pumpprints larger than 736 x 736 mm / 29 x 29 in
LEGEND:
AirJet
®
594 CRD-SAC 
TECHNICAL DATA SHEET
4
www.dct.cleaning
Dimensions (w x l x h) 2536 x 1636 x 2463 mm 99.8 x 64.4 x 96.9 in
Weight 720 Kg 1587 lbs
Ø energy consumption per cycle 1,65 kWh 1.65 kWh
Cleaning and rinsing  uid consumption
per cycle
0,05 – 0,3 l 0.01 – 0.08 gal
Compressed air consumption per cycle 83 l / 5 Bar 21.83 gal / 72.5 PSI
Max. dimensions of the cleaned parts 470 x 880 x 600 mm 18.5 x 34.65 x 23.62 in
Dimensions of the carrier basket 455 x 855 x 500 mm 17.91 x 33.66 x 19.69 in
Maximal load of the basket 50 Kg 110 lb
Dimensions of the handling trolley 570 x 1354 x 950 mm 22.44 x 53.30 x 37.40 in
Maximal load of the handling trolley 50 Kg 110 lb
Temperature range setting of the cleaning
and rinsing  uid
From ambient temperature to 60°C From ambient temperature to 140°F
Volume of the storage tanks (clean, rinse) 200 l 52.8 gal
Temperature range setting of the drying From ambient temperature to 80°C From ambient temperature to 176°F
Noise level < 70 dB < 70 dB
Device control PLC + 5,7“ touchscreen PLC + 5.7“ touchscreen
TECHNICAL PARAMETERS
DIMENSIONS MINIMUM SERVICE SPACE
AROUND THE MACHINE
600 mm
23.6 in
600 mm
23.6 in
600 mm
23.6 in
600 mm
23.6 in
2536 mm
99.8 in
2663 mm
104.8 in
1636 mm
64.4 in
metric units imperial units
2463 mm
96.9 in