00900170-01_ID_OIS_SIS_16.0_R18-2_EN_DE.pdf - 第69页
ASM OIS/SIS Datab ases 16.0 (R18 -2) / Interf ace Description 11/2018 Edition 69 30475 Z Axis, component at nozzle missing 30476 Z Axis, component at nozzle although no component expected 30477 Z Axis, component too smal…
ASM OIS/SIS Databases 16.0 (R18-2) / Interface Description 11/2018 Edition
68
21812
Component inspection failed
21813
Size check failed
21815
Flipped component detected
21816
Quality is too low for optical centering
21817
No component in front of the camera or component not bright enough
21821
Flipped component detected
21822
Quality is too low for optical centering
21823
No component in front of the camera or component not bright enough
21826
Position (approcimate) cannot be determined
21827
Angle (approcimate) cannot be determined
21828
Position (fine) cannot be determined
21831
Not all features of the component were detected
21832
Not all ball features of the component were detected
21833
Features outside positional tolerance
21834
Ball features outside positional tolerance
21838
Component hat not been dipped in flux correctly
21841
Nozzle is soiled
21842
Nozzle duct blocked
21843
Nozzle wom
21880
Measurement with 3D sensor failed
21881
Measurement with 3D sensor: Not all connections were found
21882
Measurement with 3D sensor: At least one connection is damaged
21883
Measurement with 3D sensor: Coplanarity outside tolerance
21884
Measurement with 3D sensor: Distance between component and sensor too
small
21885
Measurement with 3D sensor: Distance between component and sensor too
large
21886
Measurement with 3D sensor: Component tilted too much
22001
X-Feeder: Component was not transported into specified position in the
defined time.
22002
X-Feeder: Component was not transported into specified position in the
defined time.
22004
X-Feeder: Foil tom
22005
X-Feeder: Foil removal incorrect
22006
X-Feeder: Foil removal device blocked
22015
X-Feeder: Feeder not mounted or communication to feeder interrupted.
22017
X-Feeder: Tape drive of the feeder is not referenced
22018
X-Feeder: Low foil tension
22023
Attempt to access track without component tape
30460
Unspecific axis hardware error
ASM OIS/SIS Databases 16.0 (R18-2) / Interface Description 11/2018 Edition
69
30475
Z Axis, component at nozzle missing
30476
Z Axis, component at nozzle although no component expected
30477
Z Axis, component too small
30478
Z Axis, component too large
30622
Nozzle missing
30700
Error moving Z axis down
30701
Error moving Z axis up
30744
Component cannot be placed because skinning time has expired
30749
High component is on the nozzle
30750
Nozzle was not properly engaged when picking up nozzle
30780
Component present on nozzle before pickup
30781
Component not present on nozzle after pickup
30782
Component not present on nozzle before placement
30783
Component still present on nozzle after placement
30784
Component not present before dipping
30785
Component not present after dipping
30786
Component not present on nozzle before rejection
30787
Component still present on nozzle after rejection
30788
Component not present on nozzle before recycling
30789
Component still present on nozzle after recycling
30794
Placement aborted. The component has not touched the board
31830
Cannot pick up component
31831
Vision error occurred
31834
Component height measurement failed
31837
Foil torn. Machine was stopped to protect Z axis
33211
Measurement result has bad quality
33214
Cannot measure component. Please change to component teaching gui
33325
Field of view of camera is too small for measurement
33326
One feature is too small for measurement with SIPLACE Vision
33333
3D sensor: Components of this type cannot be measured
33334
3D sensor: Gull wing and ball connections cannot be measured
simultaneously
33335
3D sensor: Too few connections for measurement with the 3D sensor
33338
SIPLACE Vision scaling outside tolerance
33340
Component rotation angle outside tolerance
33341
Measured offset in X and Y outside feed tolerance
33342
Measured offset in X outside feed tolerance
33343
Measured offset in Y outside feed tolerance
33344
Measured lead length outside tolerance
ASM OIS/SIS Databases 16.0 (R18-2) / Interface Description 11/2018 Edition
70
33345
Measured blob area outside tolerance
33346
Position cannot be determined
33347
Component inspection failed
33348
Size check failed
33350
Flipped component detected
33351
Quality is too low for optical centering
33352
No component in front of the camera or component not bright enough
33354
Measured size outside tolerance
33355
Measured size in X outside tolerance
33356
Measured size in Y outside tolerance
33357
Measured structure size outside tolerance
33358
Position (approximate) cannot be determined
33359
Angle (approximate) cannot be determined
33360
Position (fine) cannot be determined
33361
Not all features of the component were detected
33362
Not all ball features of the component were detected
33363
Features outside positional tolerance
33364
Ball features outside positional tolerance
33365
Nozzle dirty
33366
Nozzle duct blocked
33367
Nozzle worn
33370
Component picked up at wrong angle
33371
Measurement with 3D sensor failed
33372
Measurement with 3D sensor: Not all connections were found
33373
Measurement with 3D sensor: At least one connection is damaged
33374
Measurement with 3D sensor: Coplanarity outside tolerance
33375
Measurement with 3D sensor: Distance between component and sensor too
small
33376
Measurement with 3D sensor: Distance between component and sensor too
great
33377
Measurement with 3D sensor: Component tilted too much
33380
Lead length inspection failed
33381
Measured lead length outside of tolerance
33382
Colinearity check: Lead positions outside of tolerance
33383
Measured lead width outside of tolerance
33387
Coarse position cannot be determined
33398
Glue dot inspection was unsuccessful
33399
Glue dot not within the target region
34403
Placement stopped