manual-jtse-control-unit-hot-air-0027698_ID-218375_EN.pdf - 第9页

A B A B ø ø Prot ector s No. * Ref. A x B ( mm ) A xB ( i n) No. * Ref. A x B ( mm ) A xB ( i n) P3353 4,3 x 3 0 .1 6 x 0 .1 2 P 12 4 9 12 x 23 0.47 x 0. 9 P378 6 5,2 x 5, 2 0.20 x 0. 20 44 P 4000 12, 5 x 12 , 5 0.49 x 0…

100%1 / 20
TC
Suction
OK
17:14
20
ºC
Power
45%
120ºC Selected
TC
Temp.
4m 38s
400
ºC
80
%
400ºC Selected
Protection
Hot Air Temp. Air Flow Selec.
TC
Suction
OK
JTT
TET
JT
TE
Use only with a 250V fuse
Employer uniquement avec
un fusible de 250V
TC
Suction
OK
TC
Suction
OK
17:14
20
ºC
Power
45%
120ºC Selected
TC
Temp.
4m 38s
400
ºC
80
%
400ºC Selected
Protection
Hot Air Temp. Air Flow Selec.
TC
Suction
OK
JTT
TET
JT
TE
Use only with a 250V fuse
Employer uniquement avec
un fusible de 250V
TC
Suction
OK
TC
Suction
OK
17:14
20
ºC
Power
45%
120ºC Selected
TC
Temp.
4m 38s
400
ºC
80
%
400ºC Selected
Protection
Hot Air Temp. Air Flow Selec.
TC
Suction
OK
JTT
TET
JT
TE
Use only with a 250V fuse
Employer uniquement avec
un fusible de 250V
TC
Suction
OK
8
1 2 3 4
8
We recommend using the protector + tripod We recommend using the manual extractors
Protectors & Extractors
For small components (fig. 1 and 2). For large components (fig. 3 and 4).
Position the extractor with the
appropriate suction cup and
press the suction button.
Heat the component.
The component lifts off
automatically when the solder
melts.
Operation
3. Extracting1. Placing
2. Heating
A
B
A
B
ø
ø
Protectors
No.* Ref. AxB (mm) AxB (in) No.* Ref. AxB (mm) AxB (in)
P3353 4,3 x 3 0.16 x 0.12 P1249 12 x 23 0.47 x 0.9
P3786 5,2 x 5,2 0.20 x 0.20 44 P4000 12,5 x 12,5 0.49 x 0.49
P3352 5,2 x 7,5 0.20 x 0.29 P3354 13,2 x 13,2 0.52 x 0.52
P3355 5,2 x 9,5 0.20 x 0.37 P4025 13,5 x 21,5 0.53 x 0.85
P3356 6,2 x 4,2 0.24 x 0.16 48 P2230 15 x 15 0.59 x 0.59
P3785 7, 2 x 7, 2 0.28 x 0.28 60 P4010 17 x 17 0.67 x 0.67
P3784 8,2 x 8,2 0.32 x 0.32 P4005 18 x 29 0.71 x 1.14
P4035 9 x 13 0.35 x 0.51 P4030 18,5 x 18,5 0.73 x 0.73
P4040 9,5 x 19 0.7 x 0 .74 P1068 18,5 x 24 0.73 x 0.94
P4080 9,5 x 21 9.5 x 0.83 P2685 28,5 x 28,5 1.12 x 1.12
32 P2220 10 x 10 0.39 x 0.39 P4085 31,5 x 31,5 1.24 x 1.24
P4045 10,5 x 21 0.14 x 0.82 P2672 33 x 46 1.30 x 1.18
P4090 11 x 16 0.43 x 0.63 P4002 50 x 50 1.97 x 1.97
24 P2235 12 x 17 0.47 x 0.67 P3357 52,5 x 14 2.06 x 0.55
* Corresponding number on ESHT and supplied in it.
Tripods
Ref. øC (mm) øC (in)
T2050 39 1.53
T2250 85 3.35
Manual Extractor
Ref. øD (mm) øD (in)
E2190 7 0.27
Extractors
No.* Ref. AxB (mm) AxB (in) No.* Ref. AxB (mm) AxB (in)
52 E2052 20 X 20 0.79 x 0.79 E4015 31,5 X 31,5 1.24 x 1.24
64 E2064 20 X 26 0.79 x 1.02 E2084 33 X 33 1.30 x 1.30
80 E2184 24 X 24 0.94 x 0.94 E2100 38 X 38 1.50 x 1.50
E2068 27 X 27 1.06 x 1.06 E2124 45 X 45 1.77 x 1.77
E4020 28,5 X 28,5 1.12 x 1.12
Accessories
99
40 mm
50 mm
60 mm
80 mm
100 mm
130 mm
130 mm
para manuales - negro plano
200 mm
300 mm
(not included)
TC
Suction
OK
17:14
20
ºC
Power
45%
120ºC Selected
TC
Temp.
4m 38s
400
ºC
80
%
400ºC Selected
Protection
Hot Air Temp. Air Flow Selec.
TC
Suction
OK
JTT
TET
JT
TE
Use only with a 250V fuse
Employer uniquement avec
un fusible de 250V
TC
Suction
OK
TC
Suction
OK
17:14
20
ºC
Power
45%
120ºC Selected
TC
Temp.
4m 38s
400
ºC
80
%
400ºC Selected
Protection
Hot Air Temp. Air Flow Selec.
TC
Suction
OK
JTT
TET
JT
TE
Use only with a 250V fuse
Employer uniquement avec
un fusible de 250V
TC
Suction
OK
1010
Using the Thermocouple Type K
You can choose from two work modes:
Regulation: the station regulates the air
the temperature automatically to maintain the
External Thermocouple (TC) temperature.
It is not recommended to exceed ramp-up rates over 3-4ºC / sec. (5-7ºF / sec) so as to reduce the
risk of thermal stress on the PCB.
Fix the TC with Kapton Tape (Ref. PH217) as near as possible to the component being worked on.
If Kapton tape is not ESD you must use an ionizer.
Protection: the station cuts the air supply off
when the External Thermocouple (TC)
temperature is reached.
Connect a TC type K (PH218) to the station and use it as a protection or regulation sensor.
You can define its use mode by means of the “Ext TC mode” option in the “Tool” menu.