46230811.pdf - 第15页

Page 13 DH P ositioning System Assembly , Non P/T T46230811 Rev . J This Document Supports Assembly 46230811 Rev J DET NO. ITEM NO. DESCRIPTION QTY U/M 1 48227901 BALL SCREW UN IT 2 EA 2 48253602 BELLOW,DUST 2 EA 3 BLKE0…

100%1 / 46
Page 12
T46230811 Rev. J DH Positioning System Assembly, Non P/T
This Document Supports Assembly 46230811 Rev J
Notes
1
Torque to 90 IN - LB.
2
Apply BLKM07389 (Loctite 222) ,bottom plunger then loosen 1/4 turn.
3
Lable fittings and tubing with corresponding line numbers.
4
Electrostatic discharge precautions must be used during assembly.
5
Use Loctite 242 - UIC #BLKM07402.
6
Torque screws to 70 IN-LBS.
7
Fasten with LOCTITE 495.
8
Apply Loctite 222 - UIC #BLKM07389.
9
Replace existing set screws with hardware indicated.
10
Apply Loctite 242 (BLKM07402) to threads of ball screw units and torque nut to 15 FT- LB.
11
Set up dimension from the face of the bearing bracket to the face of the pulley hub.
12
Locate the pulley on the shaft with the set screw, then tighten the two #8 cap head screws to
secure the pulley to the shaft.
13
Orient the extended hub of the bearing to the right when viewing the shaft from the front of the
machine.
14
Do not wrap cable around encoder body.
15
Lubricate ball bushings and shaft with 10W oil after assembly. Refer to X-Y rotary positioning
assembly ball bushing lubrication procedure.
16
Completely wipe off rust preventative and apply Blue Grease (BLKM07680) thoroughly to ball
screw units.
17
Apply Megnalube (40833809) to top of plunger.
18
Dowel pins to protrude from encoder plate 0.12 inches towards motor mounting casting.
19
Keep ESD cover on connectors until cable connections are attached.
20
Torque screws to 30 IN-LBS.
21
Remove existing two 10-32 x 7/8 SHCS from lock assembly and use to attach support bracket to
lock Assembly.
Page 13
DH Positioning System Assembly, Non P/T T46230811 Rev. J
This Document Supports Assembly 46230811 Rev J
DET
NO.
ITEM NO. DESCRIPTION QTY U/M
1 48227901 BALL SCREW UNIT 2 EA
2 48253602 BELLOW,DUST 2 EA
3 BLKE01630 TIE WRAP 2 EA
4 BLKM06540 NO-MAR SET SCR #10-32 X 15/64 2 EA
5 80000516 SHCS 10-32 X 5/8 13 EA
6 48226701 MACHINING, DH X MOTOR 1 EA
7 80010512 DOWEL 1/2 X DIA. X 5 1 EA
8 80005005 SSSFP 1/4-20 X 1/2 1 EA
9 22243008 VINYL DAMPING 1 EA
10 18332000 SCREW, THUMB 8 EA
11 14338000 SHAFT, Y AXIS 2 EA
12 80000521 SHCS 10-32 X 1 1/2 14 EA
13 17702003 BASE 1 EA
14 12837000 GEARBELT 2 EA
15 47082601 SWITCH 4 EA
16 80000710 SHCS 5/16-18 X 2 1 EA
17 80019002 ITLW #4 12 EA
18 14346000 SWITCH HOUSING 1 EA
19 80000304 SHCS 6-32 X 5/8 2 EA
20 80018803 FW #6 22 EA
21 80018703 SLW #6 17 EA
22 44733906 PLUG, PAINTED 7 EA
24 80008408 PHMS 4-40 X 5/8 12 EA
25 14331000 COVER, HOUSING 1 EA
26 80000103 SHCS 4-40 X 3/8 8 EA
27 80000519 SHCS 10-32 X 1 5 EA
28 BLKE01298 GROMMET 1 EA
29 14328001 PIN,ACTUATOR 4 EA
30 BLKM06319 RETAINING RING 4 EA
31 20267000 SUPPORT, BRG 1 EA
Page 14
T46230811 Rev. J DH Positioning System Assembly, Non P/T
This Document Supports Assembly 46230811 Rev J
DET
NO.
ITEM NO. DESCRIPTION QTY U/M
32 80000604 SHCS 1/4-20 X 5/8 9 EA
33 15102001 PULLEY,GEARBELT 3 EA
34 80005803 SSSCNP 10-24 X 1/2 3 EA
35 46684301 BEARING,BALL 2 EA
36 80001302 SBHS 4-40 X 3/8 6 EA
37 40834608 STANDOFF 4 EA
38 20266000 SHAFT 1 EA
39 15092000 GEARBELT 1 EA
40 46991003 RETAINER, BELLOW 1 EA
41 80000707 SHCS 5/16-18 X 1 1/4 1 EA
42 17691000 SUPPORT,BRG 1 EA
43 10593001 BEARING,BALL 2 EA
44 17689000 BLOCK,BRG 1 EA
45 80015103 HEX,JAM NUT 5/16-18 2 EA
46 14330003 RETAINER, BELLOW 2 EA
47 22260003 VINYL/.25 FOAM 1 EA
48 42039202 COVER,BOTTOM 1 EA
49 80008721 PHMS 10-32 X .38 4 EA
50 80018704 SLW #8 23 EA
51 22260002 VINYL/.25 FOAM 1 EA
52 17258075 .50 INSULATION 2 EA
53 45048001 COVER,FRONT 1 EA
55 48344301 HDW,STDF,10-32,1/2 IN,STL,M/F 2 EA
56 80018804 FW #8 18 EA
57 17656001 PLATE,MTG. 1 EA
58 80001602 SBHS 10-24 X 3/8 4 EA
59 17700001 COVER,Y FRAME 1 EA
60 80001402 SBHS 6-32 X 3/8 8 EA
61 45336503 RIGHT, COVER ASSY 1 EA
62 BLKM07423 HEX STANDOFF 7 EA