TDS_InJet_388_DOUBLE_TRIPLE_CRRD_ENG.pdf - 第3页

InJet ® 388 DOUBLE TRIPLE CRRD TECHNICAL DATA SHEET 3 www.dct.cleaning C R R Application name Recommended application Recommended temperature Total cleaning process time Capacity per 8 hours Stencil, misprint, squeegee 2…

100%1 / 8
InJet
®
388 DOUBLE TRIPLE CRRD 
TECHNICAL DATA SHEET
2
www.dct.cleaning
GENERAL INFORMATION
The InJet 388 series cleaning systems represent
unique vertical Spray-In-Air technology developed
and manufactured by DCT.
The vertically installed Spray-In-Air device minimizes the
shadowing eff ect commonly seen in horizontal cleaners,
and maximizes the effi ciency of the cleaning process as
the cleaning  uid is sprayed directly onto the cleaned
component.
InJet
®
388 DOUBLE TRIPPLE CRRD including 100%
closed loop with processes of cleaning, pre-rinsing,  nal
rinsing,
and drying technologies.
All of the processes are fully automated, and take place
in 3 process chambers. Cleaning takes place in the  rst
inlet chamber, after which the cleaned part is automatically
transported to the central chamber where the  rst rinsing
process takes place. The third, and last, outlet chamber is
designed for the  nal rinsing and the drying process.
All 3 chambers (inlet and outlet) can be used in
parallel, which increases machine’s capacity and reduces
cross-contamination when compared to single-chamber
devices. The machine has two positions on the PCB frame
(two slots), which means that at full capacity, 6 frames with
PCB are simultaneously processed.
Thus, the InJet
®
388 DOUBLE TRIPPLE CRRD delivers
twice the cleaning capacity of the InJet
®
388 TRIPPLE CRRD
and is therefore our most powerful vertical sprayer for
PCBA, for which it has also been developed.
The cleaning system can also be used for the high-capacity
removal of solder pastes and SMT adhesives from stencils,
PumPrints, squeegees and misprints.
Depending on your cleaning requirements,
the DCT project manager, in collaboration
with a local distributor, will advise you
on a suitable water-based cleaning fl uid
and the correct setup of the entire process.
InJet
®
388 DOUBLE TRIPLE CRRD 
TECHNICAL DATA SHEET
3
www.dct.cleaning
C
R
R
Application
name
Recommended
application
Recommended
temperature
Total cleaning
process time
Capacity
per 8 hours
Stencil, misprint, squeegee
20 – 40°C 68 – 104 °F 32 min. 96
PumPrint
40 – 55°C 104 – 131 °F 20 min. 96
PCB
35 – 55°C 95 – 131 °F 20 min. 1536 *
4 INDIVIDUAL PROCESSES
CLEANING PARAMETRES
C
CLEANING
PRE–RINSING
RINSING
DRYING
R
D
R
highly recommended recommended applicable
* PCB eurocards / per 8 hours (calculated for dimension of 100 x 160 mm / 3.94 x 6.3 in)
* * Parts in soldering palette / per 8 hours (320 x 500 x 50 mm / 12,6 x 19,7 x 1,97 in)
* * * Stencils, pumpprints larger than 736 x 736 mm / 29 x 29 in
LEGEND:
InJet
®
388 DOUBLE TRIPLE CRRD 
TECHNICAL DATA SHEET
4
www.dct.cleaning
TECHNICAL PARAMETERS
DIMENSIONS
MINIMUM SERVICE SPACE
AROUND THE MACHINE
3200 mm
126 in
1710 mm
67.3 in
600 mm
23.6 in
600 mm
23.6 in
600 mm
23.6 in
600 mm
23.6 in
open door
450 mm
17.7 in
open door
450 mm
17.7 in
Dimensions (w x l x h) 1710 x 3200 x 1930 mm 67.3 x 126 x 76 in
Weight 1500 kg 3307 lbs
Ø energy consumption per cycle 3,14 kWh 3.14 kWh
Cleaning and rinsing  uid consumption
per cycle
0,05 – 0,3 l 0.01 – 0.08 gal
Compressed air consumption per cycle 1 l / 5 Bar 0.26 gal / 72.5 PSI
Max. dimensions of the cleaned parts 100 x 810 x 740 mm 3.93 x 31.89 x 29.13 in
Exchangeable mechanical  lter of cleaning
and rinsing  uid
5 – 200 μm 5 – 200 μm
Spraying pressure – cleaning / 45°C / 113°F 1,6 Bar* 21.21 PSI
Range presssure – cleaning / 45°C / 113°F 0,3 – 2,8 Bar* 4.35 – 40.61 PSI
Range pressure – pre rinsing / 45°C / 113°F 0,0 – 1,5 Bar* 0.0 – 21.76 PSI
Range presssure – rinsing / 45°C / 113°F 0,1 – 1,5 Bar* 1.45 – 21.76 PSI
Cleaning  uid  ow rate 200 l / min 52.8 gal / min
Temperature range setting of the cleaning
and rinsing  uid
From ambient temperature to 60°C From ambient temperature to 140°F
Conductivity range settings of the rinsing
uid in the tanks.
0 – 2000 μS/cm * optional 0 – 2000 μS/cm * optional
Temperature range setting of the drying From ambient temperature to 80°C From ambient temperature to 176°F
Noise level < 70 dB < 70 dB
Device control PLC + 8,4“ touchscreen PLC + 8.4“ touchscreen
Volume of the storage tanks 150 l 39.6 gal
* Values may vary depending on equipment ( lters, pumps)
metric units imperial units
1930 mm
76 in