00194716-04_AI_Abwurfbehaelter_Abfrage_X-D3_de_en.pdf - 第54页

Brief Description Requirements 54 Option Verify Reject Bin Option Abfrage Abwurfbehälter

Brief Description

Requirements

Option Verify Reject Bin Option Abfrage Abwurfbehälter 53

2.3 Requirements

NOTICE

CAN nodes

The "verify component reject bin (CAN nodes)" [00116848 xx] retrofitting kit can only be used

for machines with the CAN node option.

Machines up to serial no. B751 with 1-Wire-Hub require the following parts:Machines up to se-

rial no. B751 with 1-Wire-Hub require the following parts:

An additional module/1-Wire-Hub CAT5 [03041473-xx] per location, a mounting bracket

[03023039-xx] and two screws DIN M3x6 [00201463-xx].

The machine can not be operated in mixed mode with CAN nodes and 1-Wire-Hub. Check

whether the machine has already been upgraded with the CAN node module.

If an upgrade is needed, make sure you also order the "retrofitting kit CAN nodes for CPP head"

[03079950-xx]. This upgrade can only be performed for a complete machine. See also assem-

bly instruction "CAN nodes for X series SW70x" [00196678-xx]. Conversion to CAN nodes may

only be performed by the SIPLACE Service.

► If a nozzle changer for the C&P20 or DLM6/12 is already being used, this indicates that a

1-Wire-Hub has been fitted. In this case, you do not need an extra 1 wire hub.

CAUTION

Component feed devices with prepared cable for CAN node option

Although some component feed devices already have the cables for the CAN node module

ready, the old version of the cutter control with 1-Wire-Hub is still used. In this case, you either

need to convert to the CAN node module or use the 1-Wire-Hub. Mixed configurations in the

same machine are not possible.

► Old cutter control board: [03006411-xx]

► New cutter control board for CAN node module [03052927-xx]

► From machine number B752 the component feed device has been converted fully to the

CAN node option.

► Conversion to CAN nodes may only be performed by the Siemens Service team.

NOTICE

CPP Multistar head with stationary sensors or MTC

If you use the CPP head together with a stationary camera or an MTC, you will also need the

"upgrade sensor cable reject bin" [03079030-xx]..

NOTICE

TwinHead and MTC on a machine with CAN node infrastructure

The CAN node option also requires a cutter.

Machines with the CAN node infrastructure and an MTC at a TwinHead location must use the

"upgrade sensor cable reject bin" [03079030-xx].

Brief Description

Requirements

54 Option Verify Reject Bin Option Abfrage Abwurfbehälter

Installation

Fitting the Sensors

Option Verify Reject Bin Option Abfrage Abwurfbehälter 55

3 Installation

3.1 Fitting the Sensors

► Remove the nozzle changer, if required.

► If required, loosen the component feed device and pull this slightly out of the machine.

If the 1-Wire-Hub is to be fitted in a one gantry placement area, you may need to loosen the compo-

nent feed-in device at location 2 and 4 and pull this slightly out of the machine. Please read the latest

service manual for the relevant machine prior to this.

Standard: for C&P6, C&P12, TwinHead, C&P20 and CPP

▪ Cable X series/HF R2 reject bin [03022078-xx]

▪ Sensor S1 is used for the component reject bin verify query

▪ Sensor S2 is used for the nozzle reject bin verify query

Optional: additional sensors for the CPP in pick&place mode with stationary cameras

▪ Reject bin sensors for upgrade [03079030-xx]

▪ Sensor S1 is used for the component reject bin verify query with stationary camera

▪ Sensor S2 is used for the component reject bin verify query with stationary camera at the location

with the MTC

CAUTION

Component feed device - heavy machine component

The COT insert is heavy. You may need to enlist the help of a second person.

CAUTION

Screws

When fitting the sensors S1 and S2, make sure that you do not not use any magnetic (electri-

cally conductive) screws! Only use the plastic screws provided to fasten the sensor (DIN85-

M3x6-PA [00305381-xx])!