manual-fae1-fume-extractor-0032497_ID-241531_EN.pdf - 第10页
STOP STOP # # 4 4 Cover opened or badly closed. Double check the cover. Flow Flow H M L Saturation 20% Filter Filter Carbon life 90% Aspiration ON 10 If the d is play s hows STOP# 4, power of f th e fu me ex tr actor , r…
Filter setFilter set
1 Carbon life 90%
2 Saturation 20%
3 Reset carbon
BackBack
CountersCounters
1 Total
2 Partial
BackBack
Total CountersTotal Counters
1 Plugged hrs 100
2 Idle hrs 10
3 Work area hrs 70
4 Stand hrs 20
5 Work area cys 10
BackBack
Partial CountersPartial Counters
1 Plugged hrs 100
2 Idle hrs 10
3 Work area hrs 70
4 Stand hrs 20
5 Work area cys 10
6 Reset
BackBack
4 Filter set
5 Counters
6 Program version
Main menuMain menu
Exit
1 Reset
2
Unit
3
Port
9
40 mm
50 mm
60 mm
80 mm
100 mm
130 mm
130 mm
para manuales - color gris
200 mm
300 mm
Not available for
2 workbenches
configuration
Menu Interface
Main Menu
(Original PIN: 0105)
see previous page
STOP STOP ## 44
Cover opened or badly
closed. Double check the
cover.
FlowFlow
H M L
Saturation 20%
FilterFilter
Carbon life 90%
Aspiration
ON
10
If the display shows STOP#4, power off the fume extractor, remove the cover, place it back and
secure it by using the quick release levers.
Fume Extractor Activation
Once the fume extractor is turned on, the display shows a similar screen as the following one and
the filter saturation indicator is green if the carbon filter lifetime is higher than 20%.
Troubleshooting
Station troubleshooting available on the product page at www.jbctools.com
Parameters
Important: Power off soldering stations connected to the fume extractor before
modifying any parameter.
Unit
Parameter
Continuous mode
Beep
PIN
Change PIN
Workbench
Description
Enable/disable continuous aspiration. Fume extractor aspirations remains
active independently from tool or pedal status.
Enable/disable the sound of the keypad.
Enable/disable PIN request when modifying parameters.
Change the default security PIN code.
Default PIN 0105
Select working mode for 1 or 2 workbenches (see page “Menu Interface”).
- Green: Filter OK
- Yellow: ≤ 20% carbon lifetime
or about to saturate
- Red: End of carbon lifetime
or filter saturated
11
40 mm
50 mm
60 mm
80 mm
100 mm
130 mm
130 mm
para manuales - color gris
200 mm
300 mm
Port
Parameter Description
Program
It sets the fume extractor aspiration flow. You can select between preset
and custom aspiration programs.
H (High), M (Medium) or L (Low) are the three available preset options.
Use UP and DOWN keys to switch between them while being on the main
screen.
Up to ten aspiration levels between H (High) and L (Low) can be selected
for custom program (range 10-100%). If a custom aspiration program is
selected, the selected aspiration level can be changed on the main screen.
By default, M (Medium) aspiration program is selected.
Delay to stop /
Stand
It sets the time that a fume extractor keeps aspirating fumes at the stand
once the tool is returned to it (range 0-999 seconds)
By default stand time is 60 seconds.
Delay to stop /
Work area
It sets the time that a fume extractor keeps aspirating fumes at the work
area once the tool is returned to the stand (range 0-300 seconds).
Pedal / Activation
It sets the pedal activation mode. There are two different modes: “pressed”
and “released”.
One-touch: Press the pedal once to activate aspiration. Press again to
stop aspiration.
Pressed: (Mode function must be pressed) aspiration is active as long as
the pedal is kept pressed.
By default activation is pressed.
Pedal / Mode
When the activation parameter is set to pressed, the mode parameter can
be configured to released mode. In this mode aspiration is always active
until the pedal is pressed.
By default mode is pressed.