00194598-01.pdf - 第39页
Ceramic substrate centering SIPLACE S- 27 HM 2 Retrofit instructions: ceramic substrate centering for SIPLACE S-27 HM 12/2004 Edition 39 2.3 Part s req uired 2.3.1 Contents of re trofit kit 2 Fig. 2.3 - 1 Retrofit kit fo…

2 Retrofit instructions: ceramic substrate centering for SIPLACE S-27 HM Ceramic substrate centering SIPLACE S-27 HM
12/2004 Edition
38
2.2 Safety instructions
WARNING
The safety instructions from the “Operational safety” chapter of the user manual and servicing in-
structions take precedence over these instructions. 2
The SIPLACE placement machines are supplied with mains voltage.
Consequently parts of these systems carry dangerous voltages! This voltage is present at certain
modules inside the machine base, even when the machine is switched off at the main power
switch.
Incorrect handling of the placement machine or touching live parts of the machine can result in
death or severe injury, and considerable damage to equipment.
BEFORE starting any work, shut down the operating system correctly, then switch the machine
OFF at the main power switch and disconnect from the main power supply. In addition, the com-
pressed air supply must be switched off at the compressed air unit's main valve in the machine
base and vented by actuating the needle valve on the compressed air unit.
There is DANGER for heart pacemaker wearers in the vicinity of the linear motors, as described
in detail in the "Special safety instructions for working in the vicinity of strong magnetic fields"
section of the user manual and service manual.
Always follow the accident prevention regulations, DIN or other standards and special safety
rules applicable in your country.
Pay attention to the information concerning residual voltages in the Operational Safety chapter.
Follow the ESD regulations as described in the operational safety section of the operating
instructions.
During the retrofit, always secure the machine to prevent access by other people and to prevent
it being switched on again. The procedure is described in the “Locking the machine…” section of
the user manual.
Working with the SITEST program further increases the risk of accident.
The SITEST program must only be used by authorized and trained personnel.
2
2.2.1 Definitions
2
PLEASE NOTE 2
2
2
2
Caution 2

Ceramic substrate centering SIPLACE S-27 HM 2 Retrofit instructions: ceramic substrate centering for SIPLACE S-27 HM
12/2004 Edition
39
2.3 Parts required
2.3.1 Contents of retrofit kit
2
Fig. 2.3 - 1 Retrofit kit for single conveyor + 1 lifting table

2 Retrofit instructions: ceramic substrate centering for SIPLACE S-27 HM Ceramic substrate centering SIPLACE S-27 HM
12/2004 Edition
40
2
2
2
The basic unit consists of the following parts: 2
2
2
Qty.
Item number Designation Spare part
00118571- S27 HM ceramic substrate centering, single conveyor
1 03015184- Basic ceramic substrate centering unit
2 00845023- DIN912-M4 x 6-8.8
4 00366960- Travel limitation
1 03013650- Tool for travel limitation E
1 00369723- Cable: ceramic substrate centering E
1 00366400- Lifting table bed, single conveyor option E
1 00194598- Retro. instruct. for ceramic sub. option S-27HM
Qty. Item number Designation Spare part
00118570- S27 HM ceramic substrate centering, dual conveyor
1 03015184- Basic ceramic substrate centering unit
2 00845023- DIN912-M4 x 6-8.8
4 00366960- Travel limitation
1 03013650- Tool for travel limitation E
1 00369723- Cable: ceramic substrate centering E
1 00366399- Lifting table bed, dual conveyor option E
1 00194598- Retro. instruct. for ceramic sub. option S-27HM
Qty. Item number Designation Spare part
1 03015184-xx Basic ceramic substrate centering unit
1 00347287-xx X direction carriage unit, cer.cent. HS-50
1 00347281-xx Base unit for cer. centering HS-50
1 00358874-xx Stop set 1, cer.cent. HS-50 E
1 00358875-xx Stop set 2, cer.cent. HS-50 E
1 00358876-xx Stop set 3, cer.cent. HS-50 E
1 00356032-xx-xx Pneumatic syst. ceramic cent. HS-50 E
1 00332940-xx Solenoid valve MZH-5/2-M3-L-LED E
1 00333778-xx Plastic hose PUN-6*1 blue E