00195044-16_UM_VisionTeachStation_DE_EN.pdf - 第162页
8 Starting the vision teach station Vision Teach Station User Manual 8.4 Messages when starting up for the first time after re-installation 05/2016 Edition 162 8.3.6 Camera interface card not detected or driver not insta…
Vision Teach Station User Manual 8 Starting the vision teach station
05/2016 Edition 8.3 Error messages when starting the application
161
Select "Install from a list or specific location" and enter the following directory:
C:\Program Files\Sontheim\MT_Api\7.4.14.0\Driver\PowerPCI 8
If this directory does not exist, insert the "Software Vision Teach Station" installation CD and
start the Setup.exe under the \CAN directory.
If the C167D00.SYS file is needed, you will find it in the same directory. 8
Perform a reboot in either case.
For the PowerCAN-PCI-II CAN card
This card gets installed as of 04/2012. It has no CAN3 plug.
In the Device Manager (Control Panel System Hardware Device Manager), check
whether the driver for the CAN card has been installed correctly. There must be a "PowerCAN-
PCI II Sontheim GmbH" entry under "Multifunction adapters".
8
8
8
Fig. 8.3 - 2 Device Manager with PowerCANPCI II
If you cannot find this entry, look for the "Other PCI Bridge Device" entry under "Other devices".
In this case, you will have to reinstall the driver:
Under Properties Driver tab, select the "Update Driver" button.
Select "Install from a list or specific location" and enter the following directory:
C:\Program Files (x86)\Sontheim\MT_Api\7.4.14.0\Driver\PowerPCIv2 8
If this directory does not exist, insert the "Software Vision Teach Station" installation CD and
start the Setup.exe under the \CAN directory.
Perform a reboot in either case.
8 Starting the vision teach station Vision Teach Station User Manual
8.4 Messages when starting up for the first time after re-installation 05/2016 Edition
162
8.3.6 Camera interface card not detected or driver not installed
In Device Manager on the vision computer (Control Panel System Hardware Device
Manager), check whether the driver for the CAN camera interface card has been installed
correctly. There must be a "Baumer PCI-A14" entry under "Baumer Optronic Interface Cards
Series A".
If you cannot find this entry, look for the "Coprocessor" entry. In this case, you will have to rein-
stall the driver:
Insert the "Software Vision Teach Station" installation CD.
Under Properties Drivers tab, select the "Update drivers" button.
Select "Install from a list or specific location" and enter the following directory of the installation
CD:
\CameraDriver. 8
If the boifcxdrv.sys file is needed, you will find it in the same directory.
If you cannot find the "Coprocessor" entry either, then the camera interface card is defective. 8
8.4 Messages when starting up for the first time after re-installation
After re-installation or when the software is updated, when the application is started for the first
time, it will update the firmware on the camera illumination or camera interface card.
When the "Teach Station" application is started for the first time, this may mean that the following
messages are displayed:
(1) Updating of the firmware for sensor type xx has started. This will take approximately 2
minutes. Please do not interrupt the update. This could damage the camera configuration.
(2) Firmware for the camera interface card was updated. Please shut down the computer, switch
off at the power switch and restart.
Please follow the instructions in the messages.
Vision Teach Station User Manual 8 Starting the vision teach station
05/2016 Edition 8.5 Installing the interface cards
163
8.5 Installing the interface cards
If an interface card has to be replaced, you will then have to install the drivers as follows:
8.5.1 CAN card
When the computer is restarted, Windows indicates that a new hardware component was detec-
ted. Follow the dialog.
If the driver is not automatically detected, follow the instructions in section 8.3.5, page 160.
8.5.2 Camera interface card
When you install the card, remember to plug in the floppy power supply connector again. When
the computer is restarted, Windows indicates that a new hardware component was detected.
Follow the dialog.
If the driver is not automatically detected, insert the "Software Vision Teach Station" installation
CD and enter the path for the boifcxdrv.inf file manually:
\CameraDriver. 8
Reboot the computer after installing the driver.