TM4754.TM5102.PickupMACS.pdf - 第7页

SMT Software Engineering Group IM Ope ration s Y A MAHA MOTOR CO ., L TD.  MDOC-SOFT50 177 7/ 25 Exec ute at Pick Error Select whether get No zzle MAC S a gain or not, when pickup er ror occur red. Use – Enab led, Not U…

100%1 / 25
SMT Software Engineering Group
IM Operations YAMAHA MOTOR CO., LTD.
MDOC-SOFT50177
6/25
< Contents of Feeder MACS setting items >
Items Explanation Input range Initial value
Feeder MACS
Select whether use Feeder MACS or not.
ON – Use, OFF – Not use
ON/OFF OFF
8mm Feeder Mark DB
No.1-3 (*1)
Input the mark data number for Feeder
MACS. The number for 8mm feeder
should be registered in the mark database.
It is used for Feeder MACS action in order
of 1, 2, and 3.
In case of mark data not using, input the
“0”.
0 - 300 0
4mm Feeder Mark DB
No. (*1)
Input the mark data number for Feeder
MACS. The number for 4mm feeder
should be registered in the mark database.
In case of mark data not using, input the
“0”.
0 - 300 0
Error Stop
When Feeder MACS is failed in auto
running. It stops machine running and
displays error message.
Use – Enabled, Not Use – Disabled
Use/Not Use Not Use
Correct Limit X(mm)
Correct Limit Y(mm)
Input the upper limit correction value of
Feeder MACS.
When Feeder MACS correction value
exceeds this input value, it does not
correct by Feeder MACS.
000.000–
999.999(mm)
X - 0.3(mm)
Y - 0.3(mm)
Retry interval (Minute)
(*1)
Input the time interval for retry of Feeder
MACS.
In the case of “0”, it does not retry Feeder
MACS by time interval.
0 - 480 0 (Minute)
< Contents of Nozzle MACS setting items >
Items Explanation Input range Initial value
Nozzle MACS
Select whether use Nozzle MACS or not.
ON – Use, OFF – Not use
ON/OFF OFF
Error Stop
When Nozzle MACS is failed, it stops
machine running and displays error
message.
Use – Enabled, Not Use – Disabled
Use/Not Use Not Use
Execute at Load Board
Data
Select whether get Nozzle MACS again or
not, at loading board data..
Use – Enabled, Not Use – Disabled
Use/Not Use Use
SMT Software Engineering Group
IM Operations YAMAHA MOTOR CO., LTD.
MDOC-SOFT50177
7/25
Execute at Pick Error
Select whether get Nozzle MACS again or
not, when pickup error occurred.
Use – Enabled, Not Use – Disabled
Use/Not Use Not Use
Execute at Emergency
Stop
Select whether get Nozzle MACS again or
not, when emergency stop.
When nozzle station exists the machine,
both [Emergency stop] and [Opening
Nozzle Station Sutter] are required.
Use – Enabled, Not Use – Disabled
Use/Not Use Not Use
Correct Limit X(mm)
Correct Limit Y(mm)
Input the limit correction value of Nozzle
MACS.
When Nozzle MACS correction value
exceeds the input value, it does not correct
by Nozzle MACS.
000.000–
999.999(mm)
X - 0.15(mm)
Y - 0.15(mm)
Nozzle Type and Database Number of the nozzle you want to use Nozzle MACS for are set on
the following dialog.
Fig.3.2 Select the nozzle type and setting the database number
3.2. Board data
To use Feeder MACS, Select “Automatic” on [Parts] - [Pick] - [Position Definition]. Feeder
MACS doesn’t work with “Teaching” or “Relative”.
Meanwhile, Nozzle MACS works with any of “Automatic”, “Teaching” and “Relative”.
Check the nozzle type to use
Nozzle MACS.
Input data
base number to use
Nozzle MACS.
SMT Software Engineering Group
IM Operations YAMAHA MOTOR CO., LTD.
MDOC-SOFT50177
8/25
Fig.3.3 [Parts] - [Pick]
4. Details
4.1. Feeder MACS
4.1.1. Execution Conditions
To execute Feeder MACS, it is necessary to satisfy the following conditions.
- Satisfy the setting described at “3. Setting”
- The parts are used for placement, and the feeder is attached on the correct position.
- The target feeder type is 4mm or 8mm.
4.1.2. Execution Timing
Feeder MACS is executed on the following timing.
- During auto-running, just before a pickup action of parts which satisfy the execution
conditions.
- When the [Parts Adjust] - [Pick] button is pressed for parts which satisfy the execution
conditions.
- When the [Teach] - [Trace] button is pressed for parts which satisfy the execution
conditions.
(*1) Feeder MACS is executed a pickup group unit.
However, Feeder MACS during auto-running is NOT executed until the following operations.
- Feeder detached or attached
- Feeder cast clamped on or off