00197737-07_IM_WES7_DE_EN.pdf - 第15页

Windows Embedd ed Standard 7 / Inst allation Manual 12/2017 Edition 15 The following windo w is displayed: Figure 4-2: Window " SIPLACE W indows Embedded Standard 7 Configurator " ► Click on the required ha rdw…

Windows Embedded Standard 7 / Installation Manual 12/2017 Edition

It the system partition is big enough, the Choose Recovery Option message is displayed and

one of the following options may be selected:

1. Restore existing system partition only

The system partition will be restored only.

2. Restore complete system disk

The complete hard disk will be restored.

► Select an option and confirm your selection with OK (or cancel your selection with Cancel).

The operating system is installed (may take some minutes) and thereafter the computer is

automatically rebooted several times.

When the Windows login window is displayed, the installation is completed (the first boot may take

some minutes).

► Log on as "ASM_Admin" and enter a password.

► If you install from DVD: Remove the DVD from the DVD drive.

► If you install from USB stick: Check if the "SIPLACE WES7 Configurator"

(e.g. directory _WES7_Configurator) is available for run on the USB stick under

Siplace_WES7_USB (please refer to section 4.3.3).

If not, release the USB stick and remove it from the USB interface.

► For the newer computers (iBASE, Microbox 427D) with two monitor outputs, the Clone

Displays operating mode has to be set in the display properties under Display – Multiple

Display, if required. Otherwise it might happen that only one monitor is accessed or the task

bar is only available on one of the monitors. This setting can also be made in the SIPLACE

Windows Embedded Standard 7 Configurator with the Add-ons and Touch Screen Driver

button.

► Additionally, it may be necessary to set the "Screen resolution" to 1024 x 768

(for E-series: 1280 x 1024) and enable the Scale Full Screen setting in the display

properties.under Panel Fit.

4.3.3 Choosing the Computer Configuration

► If you use the CD: Insert the "SIPLACE WES7 Configurator" software CD into the DVD drive.

► Open Windows Explorer and navigate to the DVD drive or open the directory (e.g. directory

_WES7_Configurator) that contains the "SIPLACE WES7 Configurator" on the USB stick

(removable disk name: Siplace_WES7_USB).

► Double-click on the start.hta file from the software CD or from the USB stick to start the

"SIPLACE Windows Embedded Standard 7 Configurator".

Windows Embedded Standard 7 / Installation Manual 12/2017 Edition

The following window is displayed:

Figure 4-2: Window "SIPLACE Windows Embedded Standard 7 Configurator"

► Click on the required hardware to select it and follow the further instructions displayed in the

succeeding windows.

► If necessary, enter the station IP-address for SIPLACE Pro LAN (required for a station

computer only).

The SIPLACE settings are automatically performed and the computer reboots.

After the reboot, you are logged on as Operator (station computer) or the Windows login window is

displayed (Coplan / BulkFeeder X computer).

► If no touch screen is used (Coplan / BulkFeeder X computer), remove the software CD from the

DVD drive or release the USB stick and remove it from the USB interface.

NOTICE

SIMATIC BoxPCs 627C/827C:

When shutting down a machine via the machine software GUI, the computer will be

switched off at the end and the It is now save to turn off the Computer

message will be displayed. For technical reasons, this message will not be displayed on

the SIMATIC BoxPCs 627C/827C.

Only the short No signal input or kein Eingangssignal monitor message is

displayed, thereafter the monitor LED starts flashing or changes from green to red.

Windows Embedded Standard 7 / Installation Manual 12/2017 Edition

5 Installing and Calibrating the Touch Screen

Now the touch screen has to be installed and calibrated (station computer only). For this, perform

the following steps:

► Log on as ASM_Admin and enter a password.

► In the "SIPLACE Windows Embedded Standard 7 Configurator", click on the Add-ons and

Touch Screen Driver button under Optional Installation to select and install a touch screen

driver. Follow the installation instructions.

► After installation, calibrate the touch screen as described in the installation manual for the

station software.

► Remove the software CD from the DVD drive or release the USB stick and remove it from the

USB interface.

If you have installed Windows Embedded Standard 7 on a station computer, the installation is

completed now.

► Install the SIPLACE machine software as described in the installation manual for the station

software.

If you have installed Windows Embedded Standard 7 on a Coplan / BulkFeeder X computer:

► Follow the instructions in the respective Assembly Instruction for the 3D Coplanarity Module,

item no:s. [00195344-xx] (for X-series), [00196842-xx] (for SX1/SX2) and [00197395-xx] (for

X-series S) or the instructions in the Operating Manual for BulkFeeder X, item no. [00198045-

xx] if you install Windows Embedded Standard 7 on a Coplan or BulkFeeder X computer.

► Install the SIPLACE machine software as described in the installation manual for the station

software.