00198382-03_UM_SIPLACE-CA4-V2_EN.pdf - 第83页

Instruction manual SIPLACE CA4 V2 2 Operational safety From software version 713.0 Edition 12/2019 2.6 Safety features 83 2.6.5 Hand guards at the lo cations with dummy feeders 2 Fig. 2.6 - 9 Hand guard on the component …

2 Operational safety Instruction manual SIPLACE CA4 V2

2.6 Safety features From software version 713.0 Edition 12/2019

2.6.4.2 Enabling the EMERGENCY STOP

If problems occur, the SIPLACE CA4 V2 can be stopped by pressing the EMERGENCY STOP

button.

An EMERGENCY STOP can be triggered by:

– Pressing the EMERGENCY STOP button on the SIPLACE Wafer System (SWS)

– Pressing an EMERGENCY STOP button on the SIPLACE CA4 V2

In these cases, the safety cutoffs of the SIPLACE CA4 V2 and SIPLACE Wafer System are trig-

gered and the power contactor is switched off within 100 ms or 500 ms (STOP category 1, con-

trolled shutdown with interruption of energy supply at standstill).

2.6.4.3 Resetting an EMERGENCY STOP

To reset an EMERGENCY STOP, you need to unlock the EMERGENCY STOP buttons for the SI-

PLACE CA4 V2 and the SIPLACE Wafer System (SWS).

 Find out the reason why the EMERGENCY STOP button triggered.

 Remove the cause.

 Unlock the relevant EMERGENCY STOP button for the SIPLACE CA4 V2 or the

SIPLACE Wafer System (SWS).

2.6.4.4 Resetting the lock

 Close any open protective covers/sliding doors on the SIPLACE CA4 V2.

2.6.4.5 Triggering the lock

 Open a protective cover/sliding door on the SIPLACE CA4 V2.

2.6.4.6 Safety cutoff with SIPLACE Wafer System (SWS)

The SWS safety cutoff is locked with the SIPLACE CA4 V2 so that the SWS is only active if the

safety cutoff (CSB) for the SIPLACE CA4 V2 is enabled.

When pressed, the EMERGENCY STOP button on the SWS affects the safety cutoff (CSB) for

the SIPLACE CA4 V2 by triggering the emergency stop function of the SIPLACE CA4 V2 and also

the emergency stop function of the SWS via its own safety cutoff.

Instruction manual SIPLACE CA4 V2 2 Operational safety

From software version 713.0 Edition 12/2019 2.6 Safety features

2.6.5 Hand guards at the locations with dummy feeders

Fig. 2.6 - 9 Hand guard on the component trolley locations

(1) Dummy feeder SIPLACE X, item no. 00141226-xx

WARNING

Operational

Operational safety by occupying every second location!

The operational safety of the component trolley in the SIPLACE CA4 V2 is ensured if at

least every second free location is occupied with a feeder module or hand guard (dummy

feeder).

 Fit a hand guard on the free locations of the component trolley.

 Even when configuring a holder for waffle pack trays, secure every second location

with a hand guard.

2 Operational safety Instruction manual SIPLACE CA4 V2

2.7 Residual voltages and discharge times in the placement machine From software version 713.0 Edition 12/2019

2.7 Residual voltages and discharge times in the place-

ment machine

If the EMERGENCY STOP button is pressed or the placement machine is switched off, the 300

V- intermediate circuit voltage for the gantry axes and the 160 V- intermediate circuit voltage for

the star axes will be reduced to harmless residual voltages within a very short time.

2.7.1 Energy state of the placement machine after switching off at the main power

switch

DANGER

Dangerous voltage levels!

The placement machine is supplied with 3 x 380 V~ to 3 x 415 V ± 10 %, 50/60 Hz or op-

tionally with 3 x 200 V~ to 3 x 220 V~ ± 10 %; 50/60 Hz mains voltage. Due to the use of

energy storage capacitors, parts of the system may conduct hazardous voltages for a cer-

tain time (approx. 5 minutes) even when the main switch has been switched off and the

mains plug has been disconnected.

Incorrect handling of this placement machine can therefore result in death or severe injury

or considerable damage to equipment.

 Always follow the applicable accident prevention and DIN regulations (particularly EN

60204, part 1 or IEC 60204, part 1) and the applicable regulations in your own coun-

try.

 The covers over the power supply unit may ONLY be opened by appropriately qual-

ified and trained personnel.

DANGER

Lethal voltages in the power supply unit!

The power supply unit has components (capacitors) which can still conduct potentially le-

thal voltages for approx. 5 minutes, even when the placement machine has been switched

off and the mains plug has been disconnected.

 Wait at least 5 minutes before you perform work on the power supply unit.

 Only ASM Assembly Systems GmbH&Co.KG service engineers or the machine

owner's service engineers, who have been trained by ASM, may perform work on the

power supply and the safety cutoff (CBS).