X-Series-Maintenance-Manual(1).pdf - 第111页
Major Maintenance Performing Maintenance Tasks Maintenance Tasks for C&P6/12 Head Maintenance Manual SIPLACE X Series 111 Star b rake 5.7.3.5 Star brake ► Clean the distribut or seat usin g a cottonw ool bud moistene…
Major Maintenance
Maintenance Tasks for C&P6/12 Head Performing Maintenance Tasks
110 Maintenance Manual SIPLACE X Series
Distributor (back part of head)
5.7.3.4 Distributor (back part of head)
NOTICE
You will need to dismantle the front section of the head for this maintenance work.
► Carefully remove the distributor together with the two
O-rings. For removal and installation details, read the
service manual for the respective machine.
1. O-ring vacuum distributor 3*1,2 NBR 70 B
[00320057-xx]
2. O-ring for distributor 8*1 NBR 70 B [00201179-xx]
► Carefully remove the two O-rings.
► Clean the O-rings and then grease these slightly with
UNISILKON L250L.
► Check the distributor for damage. If it is damaged
replace it with a new one.
► Wipe the distributor using a lint-free cloth moistened
with ethanol.
NOTICE! The front part of the distributor (the
side without the ball catch) may also be softened in
ethanol.
► Blow through the distributor with compressed air.
► (1) Check the ball catch for ease of movement.
Replace the entire distributor if it does not move
easily.
► Place the clean distributor and the lightly greased O-
rings on a clean surface.
Major Maintenance
Performing Maintenance Tasks Maintenance Tasks for C&P6/12 Head
Maintenance Manual SIPLACE X Series 111
Star brake
5.7.3.5 Star brake
► Clean the distributor seat using a cottonwool bud
moistened with ethanol.
CAUTION! Make sure you do not push dirt into
the vacuum opening with the cottonwool buds.
NOTICE
You will need to dismantle the front section of the head for this maintenance work.
► Check the star brake for damage and to ensure that
it is working correctly.
► Wipe the star brake with a dry lint-free cloth. Make
sure you remove all grease residues.
► Fill each of the three small holes in the star brake with
ISOFLEX TOPAS NCA 52.
► Remove excess grease with a lint-free cloth.
► Apply a thin film of grease to the surface of the star
brake.
Major Maintenance
Maintenance Tasks for C&P6/12 Head Performing Maintenance Tasks
112 Maintenance Manual SIPLACE X Series
Valve adjustment drives
5.7.3.6 Valve adjustment drives
Turning station
5.7.3.7 Turning station
NOTICE
Remove front part of head
You will need to dismantle the front section of the head for this maintenance work.
NOTICE
DLM4 at the DX series
The DLM4 head offers only one valve drive in the placement and pick-up position.
► Clean the valve adjusting drive and wipe the space
between the disk (1) and the motor mount dry with a
lint-free cloth.
► Wipe the ball bearings (2) dry with a lint-free cloth.
► Check that the ball bearing is working correctly. If you
have any problems, replace the valve adjustment
drive. For removal and installation details, read the
service manual for the respective machine.
► Remove any visible dirt.
► Repeat these steps for all valve adjustment drives.
NOTICE
Item-No. turning station
The turning stations at DLM3 and at DLM4 are different.
► Wipe the black O-ring (1) for the turning station clean
with a lint-free cloth moistened with ethanol.
► Check the O-ring for damage and replace if
necessary. For removal and installation details, read
the service manual for the respective machine.
► Check the toothed belt (2) for damage and replace if
necessary. For removal and installation details, read
the service manual for the respective machine.
NOTICE! The O-ring can be cleaned while still
installed using a cottonwool bud moistened with ethanol.