51074冲击扳手说明书.pdf - 第12页
中文 EN DE RU KO PT JA ES 51074 12 General safety warning o f electric tool: Warning: Read all warnings and instructions. F ailure to follow the warnings listed belo w and instruction may result in electric shock, fire and…
中文
EN DE RU KO PT JA ES
51074
11
2）为什么在还未拧紧时，机器就停止运转？
机器带有低压保护，在电池包电量过低时，机器不能工作，请确认电池包电量。
本机带有温度保护，当长时间满负荷工作时，电池包会过热，温保系统会启动导致机器停止运转，请将机器冷却
到常温后再继续使用。
3）为什么同一个电池包的工作时间会有长有短？
一个电池包如果放置时间过长而不使用的话，就会缩短其工作时间，这就是充电次数问题。在经过几次充电和使
用之后，这种状况就会得到改善。在干重活时，电池包的电量也会消耗的很快。不要在0℃以下或 35℃以上的环
境里充电，这同样会影响到电池包的工作表现。
保养与维护：
对机器作任何换修工作之前，请务必先拔出插头：
您的电动工具不需要再添加润滑油或进行其它保养。不要用水或化学清洗剂来清洗你的电动工具，用干布擦拭干净
就可以了。工具需储藏在干燥的环境中并保持马达通风口处的清洁。尽量不要在灰尘较大的环境中使用。
为了有利于与电池包寿命，请注意：
1 ）电池包存放：将电池包充电30％ -50％电量，存放在26℃以下环境中。
2）不超过6 个月时间，将电池包充满电使用一次。
废弃电池包的处理：
为保护自然环境，请妥善回收或处理电池包。该电池包含有锂电池。请向当地废物处理部门咨询有关回收和（/
或）处理的信息。通过使用手电钻把电池包电量耗尽，卸下电池包，用结实的胶带包裹好极片端口，避免短
路和漏电。请勿试图打开或拆取任何部件。
环境保护：
处理废弃物：
为了响应环保，对于坏损的机器、配件及包装材料必须详细加以分类处理，以便利于回收。
为方便分类回收，各塑胶部位都做有材料标识。
中文
EN DE RU KO PT JA ES
51074
12
General safety warning of electric tool:
Warning:
Read all warnings and instructions. Failure to follow the warnings listed below and instruction may result in electric shock, fire
and/or serious injury. Keep all warnings and instruction for review. "Electric tool" in all of the following warnings refers to the
electric tool driven by mains supply （wired） or the battery （wireless）.
General safety warning of electric tool - workplace:
1 ） Keep the work area clean and bright. Disordered and dark site may cause accidents.
2） Do not operate the electric tool in the explosive environment such as the flammable liquid, gas or dust. The spark generated by the
electric tool will ignite the dust or gas.
3） Operate the electric tool in the event of no children and bystanders around it. Inattention may cause the operator to lose control of
tool.
General safety warning of electric tool - electrical safety:
1 ） Plug of electric tool shall be supported by the socket. Never modify the plug in any way. Any change-over plug shall not be used for
the electric tool to be grounded. Unmodified plug and corresponding socket will reduce the risk of electric shock.
2 ） Do not contact the grounded surface such as the pipe, cooling fin and refrigerator. If your body is grounded, the risk of electric
shock will increase.
3 ） Do not expose the electric tool to the rain or moisture. Water entering the electric tool will increase the risk of electric shock.
4 ） Do not abuse the wire. Never carry, pull the electric tool with wire or pull out its plug. Keep the electric tool away from heat source,
oil, sharp edges or moving parts. Damaged or entangled cords may increase the risk of electric shock.
5 ） For the outdoor application, an external cord for outdoor use shall be used. A cord suitable for outdoor will reduce the risk of
electric shock.
6 ） If it is inevitable to operate the electric tool in the humid conditions, the residual current device （RCD） shall be used. （RCD） is
able to reduce the risk of electric shock.
General safety warning of electric tool - personal safety:
1 ） Keep alert and awake when operating the electric tool. Do not operate the electric tool when you are tired or have medication,
alcohol or a therapeutic response. Instantaneous negligence in the operation of electric tool may result in serious personal injury.
2 ） Wear the personal protective equipment. Always wear the goggles. Safety devices, such as the dust mask, anti-slip safety shoes,
helmet, listening protection, etc., are able to reduce the personal injury.
3） Prevent the accidental starting. Make sure that the tool is switched off when connecting the power supply and/or battery box,
picking up or carrying the tool. Putting the finger on the switch which is powered on or inserting the plug when the switch is turned
on may result in the danger.
4） Remove all adjustment keys or wrenches before turning on the electric tool. A wrench or key left on the rotating part of electric
tool may cause the personal injury.
5 ） Do not stretch your hands excessively, and always pay attention to the foothold and body balance. This provides excellent control of
electric tool in unexpected situations.
6） Dress properly. Do not wear loose clothing or jewelry. Keep the clothes, gloves and hair away from moving parts. Loose clothes,
accessories or long hair may get caught in moving parts.
7 ） If a device for connecting the chip conveyor and dust collector is provided, make sure that they are connected well and used
properly. These devices are able to reduce the risk of dust.
General safety warning of electric tool - use and precautions of electric tool：
中文
EN DE RU KO PT JA ES
51074
13
1 ） Do not abuse the electric tool and select the appropriate electric tool according to the application. The appropriately designed
electric tool will make your work more efficient and safer.
2 ） The electric tool shall not be used if the switch is unable to turn on/off the power. Electric tools that cannot be controlled with
switches are dangerous and shall be repaired.
3 ） Before making any adjustments, replacing the accessories or storing the electric tool, remove the plug from the power supply and/
or disengage the battery box from the tool. This protective measure will reduce the risk of accidental start of tool.
4 ） Place the unused electric tool outside the reach of children, and do not let the electric tool operated by the people who are not
familiar with the electric tool or who do not understand these instructions. The electric tool is a potential threat in the hands of
untrained users.
5 ） Maintenance of electric tool Check whether the moving parts are in place or stuck, check the parts for damage and other
conditions that affect the operation of electric tool. The damaged electric tool shall be repaired before use. Many accidents are
caused by poorly maintained electric tools.
6 ） Keep the cutting tool sharp and clean. Well-maintained tools with sharp cutting edges are not easy to get stuck and easy to control.
7 ） Use the electric tool, accessories, cutter bit, etc. in accordance with the instructions, taking into account the operating conditions
and works to be performed. Applying the electric tool for operations that do not match the purpose may be dangerous.
General safety warning of electric tool - use and precautions of battery tool:
1 ） Charge the battery only with the charger specified by the manufacturer. Unmatched charger and battery pack may cause the risk
of fire.
2 ） Use the electric tool only if a dedicated battery box is provided. Unmatched battery pack may cause the risk of damage and fire.
3 ） When the battery box is not in use, keep it away from other metal objects, such as the clip, coin, key, nail, screw or others, to
prevent one end from being connected to the other end. A short circuit at the end of battery may cause a fire.
4 ） The abuse will make the liquid splash out of the battery. Therefore, the exposure shall be avoided. In case of accidental exposure,
rinse it with water. In case of splash into the eye, seek the medical assistance. Liquid spilled from the battery may cause the
corrosion or burning.
General safety warning of electric tool - repair:
1 ） Have the qualified maintenance personnel to repair the electric tool with the same spare parts. This will ensure the safety of the
electric tool being repaired.
Professional requirements:
1 ） Be sure to take out the battery pack before repairing the machine.
2 ） Do not place the machine in the rain or water.
3 ） Do not store the battery pack above 40 ° C.
4 ） Charge the battery from 0 to 30 ° C, preferably 18 to 24 ° C.
5 ） Only use the accompanied charger and battery pack.
6 ） Avoid the short circuit of battery pack. （For example: do not make the bolts and nails touch the positive and negative poles of
battery pack）.
7 ） Do not burn the battery pack or discard it in the fire. Otherwise, an explosion may occur.
8 ） Do not charge the damaged battery pack.
9 ） Replace the damaged power cord timely.
10） Be sure to pull the plug off before removing the battery pack.
11） During the charging, it is normal for the charger and battery pack to heat up.
12） When the machine is not in use, do not insert the charged battery pack into the charger.
13） After the charging is over, please pull the battery pack off the charger immediately.
14） During the operation, it is normal for the body and battery pack to heat up.