53301开孔器说明书.pdf - 第6页
6 中文 EN DE RU KO PT JA ES 62602 规格 规格 低碳钢 不锈钢 铸铁 黄铜 铝 121 43/4 ″ 70 30 50 90 100 127 5 ″ 70 30 40 90 100 140 51/2 ″ 60 30 40 70 90 152 6 ″ 50 30 40 70 80 160 50 25 35 70 80 168 50 25 35 70 80 177 45 20 30 65 75 210 40 20…
5
中文
EN DE RU KO PT JA ES
53301/53501
规格 规格 低碳钢 不锈钢 铸铁 黄铜 铝
52 21/16″ 165 80 110 220 245
54 21/8″ 160 80 105 210 240
57 21/4″ 150 75 100 200 225
59 25/16″ 145 75 100 195 225
60 23/8″ 140 70 95 190 220
64 21/2″ 135 65 90 180 205
65 29/16″ 130 65 85 175 200
67 25/8″ 130 65 85 170 195
68 130 65 85 170 195
70 23/4″ 125 60 80 160 185
73 27/8″ 120 60 80 160 180
75 115 55 75 150 170
76 3″ 115 55 75 150 170
79 31/8″ 110 55 70 140 165
83 31/4″ 105 50 70 140 155
86 33/8″ 100 50 65 130 150
90 31/2″ 95 45 65 130 145
92 35/8″ 95 45 60 120 140
95 33/4″ 90 45 60 120 135
98 37/8″ 90 45 60 120 135
102 4″ 85 40 55 110 130
105 41/8″ 80 40 55 110 120
108 41/4″ 80 40 55 110 120
111 43/8″ 80 40 50 100 120
115 41/2″ 75 35 50 100 105
6
中文
EN DE RU KO PT JA ES
62602
规格 规格 低碳钢 不锈钢 铸铁 黄铜 铝
121 43/4″ 70 30 50 90 100
127 5″ 70 30 40 90 100
140 51/2″ 60 30 40 70 90
152 6″ 50 30 40 70 80
160 50 25 35 70 80
168 50 25 35 70 80
177 45 20 30 65 75
210 40 20 30 65 75
7
中文
EN DE RU KO PT JA ES
53301/53501
Bi-Metal Hole Saw 16mm:
Precautions:
Before use:
1）Please wear personal protective equipment including safety goggles and gloves
2）
A hole saw with a size of 30 mm or below shall be used with 53401 （hole saw drill pipe of 1,430 mm）
3）
A hole saw with a size of 32–152 mm shall be used with 53402（hole saw drill pipe of 32–152 mm）
4）Ensure that the hole saw and its drill pipe are tightly connected and correctly installed
During use:
1）Ensure that the cutting direction of the hole saw is perpendicular to the surface of the
material being cut
2）Pay attention to adding coolant to ensure the cutting speed and life of the hole saw
3）Chip removal is very important. It is recommended that chips are removed regularly to
prevent blocking the saw tooth gap
4）
It is recommended to adjust the hole saw speed according to the tachometer recommended speed table
After use:
1）The surface temperature will rise when the hole saw is operating. Please do not touch the
hole saw immediately after use to avoid burns
2）After the hole saw has completely cooled down, the quick release spring on the hole saw's
rill pipe can be used to discharge the cut circular materials. The SATA dual-metal hole saw
is designed for cutting metal and wood