00194547-03.pdf - 第45页
Installation Manual Station Software Version 601.02 SP1 Edition 10/2005 45 of 82 Menu item Note Selection options Onboard Parallel Port Sets the I/O addresses and IRQs of the parallel port: 3BC/IRQ7 Disabled Parallel Por…
Installation Manual Station Software Version 601.02 SP1 Edition 10/2005
44 of 82
Menu item Note Selection options
IDE Secondary
Slave UDMA
If Auto is set, UDMA mode is enabled for the slave on the
secondary IDE channel if it is supported by the disk.
Auto
;
Disabled
UDMA66/100 with 40
Wire
In the specification for UDMA66 and UDMA100, an 80-wire
cable is prescribed. You can use this option to run drives
which support these modes with a short 40-port cable on
the secondary IDE channel. If the drive is connected with
an 80-port cable, this entry is ignored and UDMA66 and
UDMA100 are set if the drive supports these modes.
Disabled
;
Enabled
IDE HDD Block
Mode
This enables the transfer of entire blocks from the hard
disk to the memory instead of individual sectors.
Enabled
Disabled
USB Controller
If this setting is disabled, the USB controller is disabled
and no USB devices can be run on the module.
Enabled
Disabled
USB Keyboard
Support
When this option is switched on, a keyboard is supported
on the USB port even after the boot process.
Enabled
Disabled
USB Mouse Support
When this option is switched on, a mouse is supported on
the USB port even after the boot process.
Enabled
Disabled
Init Display First
This option can be used to specify which graphics adapter
is to be used to output video if a PCI graphics adapter is
integrated in the system in addition to the onboard
graphics adapter. If a graphics adapter is connected to the
SMP16 bus, this is always used to output video
irrespective of the setting.
Onboard
PCI Slot
AC 97 Audio
If an AC 97 audio controller is connected to the RPIO, it
can be switched on here
Enabled
Disabled
AC 97 Modem
If an AC 97 modem controller is connected to the RPIO, it
can be switched on here
Enabled
Disabled
Onboard LAN
Disabled disables the onboard LAN controller. Enabled
Disabled
Onboard LAN Boot
ROM
In order to boot from the onboard LAN controller, this item
must be enabled.
Enabled
Disabled
Onboard FDC
Controller
Enables the onboard floppy controller
Enabled
Disabled
Onboard Serial
Port 1
Sets the I/O addresses and IRQs of serial port 1 (COM A) 3F8/IRQ4
2F8/IRQ3
3E8/IRQ4
2E8/IRQ3
Disabled
Onboard Serial
Port 2
Sets the I/O addresses and IRQs of serial port 2 (COM B): 3F8/IRQ4
2F8/IRQ3
3E8/IRQ4
2E8/IRQ3
Disabled
Installation Manual Station Software Version 601.02 SP1 Edition 10/2005
45 of 82
Menu item Note Selection options
Onboard Parallel
Port
Sets the I/O addresses and IRQs of the parallel port: 3BC/IRQ7
Disabled
Parallel Port Mode
Sets the mode of the parallel port. This option can be set
when disabled is not set for Onboard Parallel Port
Default
SPP
EPP1.7
EPP1.9
ECP
ECP+EPP
ECP Mode Use DMA
This option can only be set if ECP or ECP+EPP is selected
for Parallel Port Mode.
1
3
Installation Manual Station Software Version 601.02 SP1 Edition 10/2005
46 of 82
4.5.1.10 Setup page "IMC Miscellaneous"
In the "Selection options" column, the setting for fail-safe default is indicated in italics and the setting
for optimized default is underlined
.
Menu item Note Selection options
Priority for PCI
Bridge
Assigns a higher priority to the PCI bridge to the CPCI bus
in busmaster operation. This may be needed if high data
transfer rates between the CPCI bus and RAM are
required.
Normal
High
Boot Delay
This can be used to set a delay during which the BIOS
waits until the operating system has been booted.
Disabled
15 Sec.
30 Sec.
45 Sec.
60 Sec
1:30 Min.
2 Min.
3 Min.
5 Min.
10 Min.
Enable CTRL-
C/CTRL-Break
When No is entered, the keystrokes <CTRL-C>/<CTRL-
Break> are trapped by the BIOS and not passed on to the
operating system. The keys can be re-enabled by entering
Yes. This function can also be changed by the user during
live operation. If a software interrupt of 16h is triggered
with AH = 3, AL = 49h and BL = 0, <CTRL-C>/<CTRL-
Break> is permitted, and these key combinations are
suppressed with BL = 1.
Yes
No
SMP16-Bus
If this option is set to disabled, the SMP16 bus will be
switched to high resistance after the boot process.
Adapters on this bus cannot be accessed.
Enabled
Disabled
SMP16-Clocks
This option can be used to switch off the 8.33 MHz and
14.131 MHz clock cycle of the SMP16 bus. This setting is
only possible when the SMP16 bus is enabled.
Enabled
Disabled
8 Bit I/O Recovery
Time
Number of additional ISA clock cycles between two 8-bit
I/O accesses to the SMP16 bus.
1
1 ... 16
16 Bit I/O Recovery
Time
Number of additional ISA clock cycles between two 16-bit
I/O accesses to the SMP16 bus.
1
1 ... 16
Use of LED L1
LAN speed:
The LED is lit when the onboard LAN
is activated and the
transfer speed is100MB
User:
The LED can be switched on/off by the
user
(Bit 1 of I/O address 5400H)
LAN speed:
User