00194547-03.pdf - 第77页
Installation Manual Station Software Version 601.02 SP1 Edition 10/2005 77 of 82 Menu item Note Selection options Settings Note CPU THRM- Throttling If the system begins to throttle due to a thermal overload, this is the…
Installation Manual Station Software Version 601.02 SP1 Edition 10/2005
76 of 82
Menu item Note Selection options Settings Note
Video Off
Method
This sets the way in which the monitor is switched to
power saving mode. There are three options available:
DPMS (Display Power Management)
enables the BIOS to control
DPMS-capable graphics cards.
Blank Screen Darkens the screen and
should be used with monitors
without Power Management
functions.
V/H Sync+Blank Darkens the screen by switching
off the vertical and horizontal
synchronization.
Blank Screen
V/H Sync+Blank
DPMS
DPMS
Video Off In
Suspend
Specifies whether the monitor interface is switched off in
suspend mode (no sync signals)
No
Yes
Yes
MODEM Use IRQ
This option determines which IRQ registers the ring tone
of the modem for faxing.
NA; 3; 4; 5; 7;9; 10;
11
NA
Suspend Mode
The time is set here before the system switches to
suspend mode.
Disabled;
1 Min; 2 Min;
4 Min; 8 Min;
12 Min; 20 Min;
30 Min; 40 Min;
1 Hour
Disabled
HDD Power
Down
The time is set here after which the hard disk is switched
to Power Down mode
Disabled;
1 Min; 2 Min;
3 Min; 4 Min;
5 Min; 6 Min;
7 Min; 8 Min;
9 Min; 10 Min;
11 Min; 12 Min;
13 Min; 14 Min;
15 Min
Disabled
Installation Manual Station Software Version 601.02 SP1 Edition 10/2005
77 of 82
Menu item Note Selection options Settings Note
CPU THRM-
Throttling
If the system begins to throttle due to a thermal overload,
this is the ratio in percent: switch-off time / (switch-off
time + on time). This value is factory set and cannot be
changed.
87,5%
87,5% Item is Show
Only
Resume by
Alarm
If this option is switched on, the computer is retrieved
from power saving mode at the specified date and time. If
0 is specified as a date, this is done on a daily basis.
Enabled
Disabled
Disabled
Date (of Month)
Alarm
all values between 0
and 31
0
all values
between 0
and 31
Time (hh:mm:ss)
Alarm
valid time
0:0:0
valid time
0:0:0
Reload Global
Timer Events
Every event of a device listed below resets the global
counter for suspend mode, if this is enabled.
Enabled
Disabled
Disabled Menu item
FDD,COM,L
PT Post not
available with
Legacy Free
Installation Manual Station Software Version 601.02 SP1 Edition 10/2005
78 of 82
4.7.7 Setup page "PNP/PCI Configuration"
Menu item Note Selection options Settings Note
PNP OS
Installed
Yes, if the operating system used is plug and play-
compatible (e.g. Win9x); No, if it is not
No
Yes
No
Reset
Configuration
Data
Enabled instructs the PNP BIOS to reset all devices and
assignments.
Enabled
Disabled
Disabled
Resources
Controlled By
The Manual setting can be used to reserve the interrupts
and DMA, otherwise they will automatically be assigned
by the BIOS (PnP Extension).
If no PNP operating system has been installed, use Auto.
Auto (ESCD)
Manual
Auto
(ESCD)
IRQ Resources
This field is only enabled if the option Manual is enabled
under Resources Controlled By. Pressing the Enter key
will display a submenu in which the interrupts can be
released for assignment by the PNP BIOS (setting
PCI/ISA PnP) or not assigned by the PNP BIOS (setting
Legacy ISA)
PCI/ISA PnP
Legacy ISA
PCI/ISA
PnP
(PCI Device
for Legacy
Free)
With Legacy
Free, the options
are:
PCI Device
Reserved
DMA Resources
This field is only enabled if the option Manual is enabled
under Resources Controlled By. Pressing the Enter key
will display a submenu in which the DMA channels to be
assigned by the PNP BIOS are disabled (setting PCI/ISA
PnP) or not assigned by the PNP BIOS (setting Legacy
ISA)
PCI/ISA PnP
Legacy ISA
PCI/ISA
PnP
Menu item not
available with
Legacy Free
PCI/VGA Palette
Snoop
Color reproduction may be corrupted with some graphics
adapters such as graphics accelerators or MPEG
adapters which do not conform to the VGA standard. In
this case, set Enabled
Enabled
Disabled
Disabled
Assign IRQ for
USB
Enabled assigns a PCI IRQ to the USB controller. Enabled
Disabled
Enabled