00197402-01 AI X-Feeder Upgrade Package.pdf - 第28页
Required parts Content retrofit package 28 AI X-Feeder Upgrade Package AI X-Feeder Upgrade Packa ge 2.2 2 . 2 C o n t e n t r e t r o f it p a c k a g e Content retrofit package 1. Stuffing gear interlocked 2. Stripping …
Required parts
Re-used parts
AI X-Feeder Upgrade Package AI X-Feeder Upgrade Package 27
2
2 Required parts
Required parts
The X-Feeder upgrade package includes all parts to be replaced, for your service / maintenance person
-
nel to enable the automatically perform of retrofitting .
2.1
2.1 Re-used parts
Re-used parts
NOTICE
Reuse of component parts
For the retrofit will be used component parts. Please therefore ensure no dismantled parts to
lose.
NOTICE
Small parts
For greater clarity, we recommend that you loosen the same types of screws together and then
keep them in small, marked bowls.
CAUTION
Surface
Perform the upgrade on a one stable, level and clean surface.
1. Bearing shafts rocker
2. Bolt for Stripping Device Foil Disposal
3. Screw bolts with cover foil disposal
4. Axis D4 foil rocker assembly
5. Compression spring
Required parts
Content retrofit package
28 AI X-Feeder Upgrade Package AI X-Feeder Upgrade Package
2.2
2.2 Content retrofit package
Content retrofit package
1. Stuffing gear interlocked
2. Stripping Device Foil Disposal
3. Sticker upgrade package
4. ISO4762 - M2 x 5-A2-70
5. ISO 7046-2-M2 x 4-A2-70-H
6. Flap / tape disposal complete
(No for X104)
7. Use cover strip rocker
8. Creasing rollers / PSA
9. Deflection sheet rocker (no for X16)
10. Stuffing gear interlocked complete rocker
11. Rocker (no for X16)
X-Feeder Upgrade Install
Removing the Left Side Cover
AI X-Feeder Upgrade Package AI X-Feeder Upgrade Package 29
3
3 X-Feeder Upgrade Install
X-Feeder Upgrade Install
3.1
3.1 Removing the Left Side Cover
Removing the Left Side Cover
3.2
3.2 Remove the cable connection to the distribution board
Remove the cable connection to the distribution board
Tools required:
▪ Phillips screwdriver
▪ TORX screwdriver size T8
► Carefully place the feeder module with the right-side
side down on a stable, level and clean surface.
► Loosen the screws as shown in the diagram.
Green arrows point to the screws for which you need a
TORX screwdriver with a torque of 0.6 Nm.
Blue arrows point to the screws for which you need a Phil
-
lips screwdriver with a torque of 0.9 Nm.
Start to loosen the screws at the position shown by the
green arrow.
► Lift the back of the side cover.
► Pull the side cover at a slight angle towards the back.
Make sure that you pull the lug straight out of the
drive unit.
► Place the side cover down on a clean, safe surface.
► (1) Pull the connector marked in the diagram up and
out of its connection.
To loosen the connector, move it carefully from side
to side.
► (2) Pull the connector marked in the diagram out of its
connection in the direction of the arrow. Pull on the
connector and NOT on the cable.
► (3) Carefully swing the lock on the flat ribbon cable
connection up to the left and release the flat ribbon
cable.
Make sure that the lock is not pushed too far back. It
could break off if you do this.
► Pull the connector shown in the diagram out of its
connection in the direction of the arrow. Pull on the
connector and NOT on the cable.