00197402-01 AI X-Feeder Upgrade Package.pdf - 第31页

X-Feeder Upgrade Install Replacing the stuffing gear and parts of the co ver strip rocker AI X-Feeder Upgrade Package AI X-Feeder Upgrade Packa ge 31 3.5 3 . 5 R e p la c in g t h e s t u f f in g g e a r a n d p a r t s…

X-Feeder Upgrade Install

Remove the screws on the right side of the feeder

30 AI X-Feeder Upgrade Package AI X-Feeder Upgrade Package

3.3

3.3 Remove the screws on the right side of the feeder

Remove the screws on the right side of the feeder

3.4

3.4 Dismantle of foil drive

Dismantle of foil drive

Tools required:

▪ Flat bladed (slotted) screwdriver

▪ hexagon socket 2

▪ TORX screwdriver size T8

▪ Split pin punch 1.4

► Carefully place the feeder module down on its left

side.

► (1) Loosen the screws of the foil container.

► (2) Remove the shaft and roller of the cover strip

rocker.

► (3) Press the rocker as far till it stop, into the spring,

to relieve the bearing shaft.

► Release the bearing shaft and remove the rocker.

Place the feeder carefully on a protected and cleaned

place.

Tools required:

▪ Phillips screwdriver

▪ TORX screwdriver size T8

► (1) Loosen the screws marked in the diagram.

► Turn the foil disposal drive over.

► (2) Loosen the screw marked in the diagram.

► (3) Loosen the screws marked in the diagram.

X-Feeder Upgrade Install

Replacing the stuffing gear and parts of the cover strip rocker

AI X-Feeder Upgrade Package AI X-Feeder Upgrade Package 31

3.5

3.5 Replacing the stuffing gear and parts of the cover strip rocker

Replacing the stuffing gear and parts of the cover strip rocker

Tools required:

▪ Hexagon socket Gr. 2

▪ Phillips screwdriver

▪ Flat bladed (slotted) screwdriver

▪ Tweezers

► (1) Loosen the screws marked in the figure, at the top

and bottom of the stripping device. Depending on the

width of the feeder module, there will be up to a total

of 4 screws to be loosened at the top and bottom.

► (2) Loosen the screws on the cover sheet of disposal

drive.

► Lift the cover plate off the foil disposal drive.

► (1) Lift the gear stages with tweezers from the foil dis

posal drive.

Attention: The stage gear is greasy!

► (2) Remove the knurled stuffing gear and replace it

with the new "interlocked complete stuffing gear."

► Make sure that the corresponding washers are on the

toothed wheel axes (1).

► Place the cover plate on the slide disposal drive.

Make sure that the cover plate engages on the

toothed wheel axes (2) and the cover plate lies flat

level on the side cover.

► Fix the cover plate with the countersunk screws

marked in the diagram.

X-Feeder Upgrade Install

Replace parts of the rocker

32 AI X-Feeder Upgrade Package AI X-Feeder Upgrade Package

3.6

3.6 Replace parts of the rocker

Replace parts of the rocker

3.7

3.7 Fitting the Flap Tape Disposal

Fitting the Flap Tape Disposal

► (1) Screw the new scraper plate, with the original

screws, slide the drive disposal, starting with the

overhead screws.

► Install the new folding roller (2) with the original shaft

and screw.

► Insert the "use foil wing" (3) and mount it with the orig

inal wave.

Caution! The originally present role is not needed and

is omitted.

Tools required:

▪ Phillips screwdriver

▪ Flat bladed (slotted) screwdriver

► (1) Remove the marked in the figure bearing shaft

from the old rocker.

► Insert the new stuffing gear (3) as shown in the new

rocker (4) and secure it with the previously removed

bearing shaft (2). Make sure that the stuffing gear can

move freely in the rocker.

► Insert the new wiper sheet (5) and secure it with the

screws, starting with the overhead screws.

► Open the flap.

► Replace the existing door carefully from the feeder.

► Place the new cover slowly in a foil container. The

spring (1) it is overridden. It is not necessary since the

function is now performed by the magnet (2).