00197402-01 AI X-Feeder Upgrade Package.pdf - 第33页

X-Feeder Upgrade Install Cover foil disposal install AI X-Feeder Upgrade Package AI X-Feeder Upgrade Packa ge 33 3.8 3 . 8 C o v e r f o il d is p o s a l in s t a ll Cover foil disposal install Tools required: ▪ Phillip…

X-Feeder Upgrade Install

Replace parts of the rocker

32 AI X-Feeder Upgrade Package AI X-Feeder Upgrade Package

3.6

3.6 Replace parts of the rocker

Replace parts of the rocker

3.7

3.7 Fitting the Flap Tape Disposal

Fitting the Flap Tape Disposal

► (1) Screw the new scraper plate, with the original

screws, slide the drive disposal, starting with the

overhead screws.

► Install the new folding roller (2) with the original shaft

and screw.

► Insert the "use foil wing" (3) and mount it with the orig

inal wave.

Caution! The originally present role is not needed and

is omitted.

Tools required:

▪ Phillips screwdriver

▪ Flat bladed (slotted) screwdriver

► (1) Remove the marked in the figure bearing shaft

from the old rocker.

► Insert the new stuffing gear (3) as shown in the new

rocker (4) and secure it with the previously removed

bearing shaft (2). Make sure that the stuffing gear can

move freely in the rocker.

► Insert the new wiper sheet (5) and secure it with the

screws, starting with the overhead screws.

► Open the flap.

► Replace the existing door carefully from the feeder.

► Place the new cover slowly in a foil container. The

spring (1) it is overridden. It is not necessary since the

function is now performed by the magnet (2).

X-Feeder Upgrade Install

Cover foil disposal install

AI X-Feeder Upgrade Package AI X-Feeder Upgrade Package 33

3.8

3.8 Cover foil disposal install

Cover foil disposal install

Tools required:

▪ Phillips screwdriver

▪ TORX screwdriver size T8

► (1) Press the foil disposal drive in the direction of the

arrow and into the foil container.

► Attach the film drive with the marked cylinder head

bolts. Be sure to insert the shims.

► (2) Fix the foil disposal drive into place with the cylin

der head screw marked in the diagram.

► (3) Turn the foil disposal to drive again and attach the

spacer to the marked in the figure Torx screws. Note

the correct position of the rubber seals (4).

► (1) Carefully place the feeder module down on its left

side. Position the foil container so that it is aligned

against the side cover.

► (2) Loosen the screws marked in the diagram.

► (1) Insert the flat ribbon cable into the connection, as

far as the stop. Make sure that the blue surface at the

end of the cable is at the top and that the flat ribbon

cable lies straight in the connection. Swing the lock

down onto the flat ribbon cable.

► (2) and (3) Carefully insert the connector in the direc

tion of the arrow, as far as the stop, into the connec

tion shown.

► (4) Insert the other connector into the connection

marked in the diagram.

X-Feeder Upgrade Install

Installing the rocker on the foil container

34 AI X-Feeder Upgrade Package AI X-Feeder Upgrade Package

3.9

3.9 Installing the rocker on the foil container

Installing the rocker on the foil container

3.10

3.10 Fitting the Left Side Cover

Fitting the Left Side Cover

Tools required:

▪ Flat bladed (slotted) screwdriver

► (1) Insert the spring into the provided opening .

► Position the rocker with the recess onto the spring.

► (2) Position the rocker so that you can see the open

hole for the bearing shaft through the rocker.

► Press the rocker into the spring, to relieve the bearing

shaft thread during fitting.

► Set the bearing shaft into the hole provided and turn

to tighten.

Tools required:

▪ Phillips screwdriver

▪ TORX screwdriver size T8

► Carefully place the feeder module with the right-side

side down on a stable, level and clean surface.

► (1) Lift the side cover onto the feeder module at a

slant and from the right-hand side.

(2) Make sure that the lugs insert into the drive unit.

► (3) Make sure that the side cover is aligned with the

operating panel.

► Screw the side cover onto the feeder module, as

shown in the following diagrams. Start with screw (A)

on the right, under the operating panel.

Green arrows point to the screws for which you need a

TORX screwdriver with a torque of 0.6 Nm.

Blue arrows point to the screws for which you need a Phil

lips screwdriver with a torque of 0.9 Nm.