SECS GEM Manual.pdf - 第44页
GEM Manual for DEK Printers Capabilities Issue 1.6 January 22, 2018 Page 44 of 171 4.7 Equipment Terminal Servi ces This capability enables factory operator s to exchange messages with the host. It is particularly useful…
GEM Manual for DEK Printers Capabilities
Issue 1.6 January 22, 2018 Page 43 of 171
Material Movement
Material tracking can be performed by enabling the following events. Event reporting is
covered in Section 7.
EVENT
CEID
DESCRIPTION REFERENCE
31258 Paste dispensing. Paste dispense cycle started.
31259 Paste cartridge empty. Paste cartridge detected empty.
31264 Setup started. Setup page has been entered.
31265 Process program loaded. Process program loaded into printer.
31266 New process program. New process program created and loaded.
31268 Screen unloaded. Screen just unloaded.
31269 Screen loaded. Screen just loaded.
31270 Tool change started. Tool Change page just entered.
31271 Tool change complete. Tool Change page just exited.
31272 Setup ended. Setup page just exited.
31273 Start print cycle. Print cycle/s just started.
31274 Board received. Board received at input sensor.
31275 End print cycle. Print cycle/s just completed.
31276 Printed board ready. Board at output sensor.
31277 Board printed. Board just printed.
31301 No cleaner paper. Cleaner run out of paper.
31302 No cleaner solvent. Cleaner run out of solvent.
31319 Board delivered / removed. Board has left the machine.
Scenario:
Material sent to / removed from equipment:
Comments Host Equipment Comments
<-- S6F11 Material movement CEID
Host acknowledges report. S6F12 -->
GEM Manual for DEK Printers Capabilities
Issue 1.6 January 22, 2018 Page 44 of 171
4.7 Equipment Terminal Services
This capability enables factory operators to exchange messages with the host. It is particularly
useful for passing instructions to the operator.
When the host sends a terminal message to a DEK printer, an indication of a message is
displayed at the equipment console. This indication message will remain displayed until either,
the operator presses a button indicating it has been read or, the host sends a new zero length
text. When the operator presses the read complete button, an event report CEID is sent to the
host.
The operator can enter a terminal message, at the equipment console, which will then be sent to
the host.
For Operator procedures see Appendix B.
Terminal Services State Model:
The terminal services state model is implemented on the DEK printer.
State Diagram:
State Definitions:
Idle - No host text is displayed on the terminal.
Not Acknowledged - Host text is displayed and not yet acknowledged by the operator.
Transition Table:
Current State Trigger New State Action Comment
1 Idle Host display message. Not Acknowledged Display Waiting for operator button
2 Not Acknowledged Operator Acknowledge Idle none
3 Not Acknowledged New host message Not Acknowledged Display Waiting for operator button
4 Not Acknowledged New zero length message Idle none
IDLE
NOT
ACKNOWLEDGE
D
1
2
3
4
GEM Manual for DEK Printers Capabilities
Issue 1.6 January 22, 2018 Page 45 of 171
Scenarios:
Host sends message to equipment display:
Comments Host Equipment Comments
Host sends text for display S10F3 -->
<-- S10F4 Acknowledge sent and text displayed.
Operator reads message and presses button
<-- S6F11
[IF] Acknowledge Terminal Message event
enabled [THEN] send event report
1
.
Host acknowledges event. S6F12 -->
Host sends message to equipment display and queue behind last message:
Comments Host Equipment Comments
Host sends single line text for display S10F3 -->
<-- S10F4 Acknowledge sent and text displayed.
Host sends single line text for display
that is overwritten.
S10F3 -->
<-- S10F4 Acknowledge sent and text displayed.
<-- S6F11
Operator reads first message and presses Accept
button.
[IF] Acknowledge Terminal Message event
enabled [THEN] send event report.
Second message will be displayed.
Operator reads second message and presses
Accept button
[IF] Acknowledge Terminal Message event
enabled [THEN] send event report.
Host acknowledges event. S6F12 -->
Host sends multiple lines message to equipment display:
Comments Host Equipment Comments
Host sends multiple text for display S10F5 -->
<-- S10F6 Acknowledge sent and text displayed.
[IF] text page contains more lines then page size
[THEN] Up/Down key will be available to scroll
through message.
Operator reads message and presses Accept
button.
<-- S6F11
[IF] Acknowledge Terminal Message event
enabled [THEN] send event report
2
.
Host acknowledges event. S6F12 -->
1
See section 7-6 Acknowledge Terminal Message
Event.
2
See section 7-6 Acknowledge Terminal Message
Event.