00197469-02_SM_Twin_Kunde_EN.pdf - 第8页

1 Introduction 1.3 Staff qualifications and training 8 Service Manual SIPLACE TwinStar (Twin, Twin HF, Twin VHF) 07/2020 1.2.7 SIPLACE on the World Wide Web (WWW) Log in to our SIPLACE® homepage at http://www.asm-smt.com…

1 Introduction

1.2 Other instructions

Service Manual SIPLACE TwinStar (Twin, Twin HF, Twin VHF) 07/2020 7

1.2.4.3 Handling ESD modules

As a general rule: Only touch electronic modules if you must carry out work on the modules. In that

case, make sure that you do not touch the pins or printed conductors when you pick up flat mod-

ules.

Only touch components if you are earthed by one of the following measures:

●

You are wearing an ESD wristband.

●

You are wearing ESD shoes.

●

You are wearing ESD shoe earthing strips on an ESD floor.

Immediately before you touch an electronic module, discharge your own body by touching a con-

ductive and earthed object (such as unpainted parts of a switch cabinet, a water pipe, etc.).

Do not allow modules with chargeable and highly insulating materials to touch one another, e.g.

plastic films, insulating table surfaces or items of clothing made from synthetic fibers.

Always place the modules on a conductive surface (table with an ESD coating, conductive ESD

foam, ESD bag or container).

Do not move the assemblies near to data view devices, monitors or television units. Keep a min-

imum distance of 10 cm to monitors.

1.2.4.4 Measurements and modifications to ESD modules

Only perform measurements on modules if one of the following conditions is fulfilled:

●

You are using an earthed measuring device (e.g. via PE conductors).

●

You are using a potential-free measuring device and discharge the measuring head before

the measurement (e.g.by touching an unpainted metal part of the controller casing).

► Always use an earthed soldering iron if you carry out any soldering work.

1.2.4.5 Dispatching ESD modules

► Always store modules and components in conductive packaging (e.g. metallized plastic bags

or metal sleeves) and dispatch them in conductive packaging

► If the packaging is not conductive, place the modules in a conductive envelope before pack-

aging. Use conductive expanded rubber, ESD bags, domestic aluminum foil or paper, for

example. NEVER use plastic bags or film.

► If the module has integral batteries, ensure that the conductive packaging does not touch or

short circuit the battery terminals and, if necessary, first cover the terminals with insulating

tape or material.

1.2.5 Validity of Document

This document contains service work instructions for all SIPLACE placement heads of type Twin,

Twin HF and Twin VHF.

The service work described in this manual is largely identical for all head types:

●

If the work required should differ from the standard procedure, this will be indicated with refer-

ence to the head type and delivery state.

●

Diagrams should be seen as examples e.g. the diagram of a SIPLACE Twin HF or a different

paint finish does not mean that the following information only applies to the type shown.

The manual focuses on describing mechanical service work.

Please refer to the circuit diagram folder for any electrical checks.

1.2.6 Release History

Release Amendments

07/2013 Initial release

07/2020 The document has been completely revised.

The placement heads Pick&Place module High Force R2 [03097486‑xx] and

Pick&Place module THK R2 [03097485‑xx] have been supplemented.

1 Introduction

1.3 Staff qualifications and training

8 Service Manual SIPLACE TwinStar (Twin, Twin HF, Twin VHF) 07/2020

1.2.7 SIPLACE on the World Wide Web (WWW)

You can choose between the German and English version.

The different sections contain information about our products, services and contact persons.

In addition, registered customers can also access the MySIPLACE user group. Here, you can

access special information about our placement systems, e.g.:

●

Technical documentation

●

Technical information

●

Spare parts lists

Registration for the MySIPLACE user group is very simple:

► Click on MyASM and then on Registrieren.

► Fill in the registration form and send it off to us.

Soon afterwards, you will receive your access authorization with user name and password.

1.3 Staff qualifications and training

Qualified or adequately trained personnel means that these people are familiar with the setting up,

operation and maintenance of the machine and the add-on devices and are suitably qualified, e.g.:

●

Have been trained, instructed or authorized to switch on and off, isolate, earth and identify

electrical circuits and system components in accordance with normal safety standards.

●

Have been trained or instructed in the upkeep and use of appropriate safety equipment in

accordance with normal safety standards.

1.4 Abbreviations

Abbreviations Description

PA, PA1, PA2 Placement area, Placement area 1, Placement area 2

CO Component

C&P Collect&Place

CPP Collect&Pick&Place head

CPx Collective term for CPP, CP20, CP12 and/or CP6

PRV Pressure control valve

ESD Electrostatic sensitive device

EMC Electromagnetic compatibility

FS Function state

The last two numbers form an item number.

HF High Force

HMK Head Maintenance Kit

PCB Board

P&P Pick&Place

TH TwinHead

VHF Very High Force

1 Introduction

1.5 Tools required, measuring equipment and materials

Service Manual SIPLACE TwinStar (Twin, Twin HF, Twin VHF) 07/2020 9

1.5 Tools required, measuring equipment and materials

Before starting work, make sure that all the necessary tools and materials are available.

●

As a basic configuration we recommend the "Head Maintenance Kit for CPx" [03109541‑xx]

(see below).

The HMK contains many of the tools and materials needed for service work. Any additional

materials needed will be listed separately.

Please also observe the technical information "Head Maintenance und Exchange

Kit" [DE:TI2017‑09D05] [EN:TI2017‑09E05].

●

We also recommend using the head mount [03056231‑xx].

●

The spare parts required can be found in the chapters concerned.

●

For more information refer to the service section of our homepage at www.siplace.com.

Head Maintenance Kit (HMK)

Fig.2: Overview – Head Maintenance Kit for CPx [03109541‑xx].

NOTICE

Various configuration stages

Your HMK may not contain all the materials shown, depending on its configuration stage.

Tools contained in the HMK: Item no.

T03 Anti-static tweezers, Bernstein 5-192 00377393-xx

T07 Torque screwdriver ESD 1.0-5.0 Nm 03078400-xx

T08 Bit holder for TorqueVario screwdriver 03078706-xx

T09 Extension/ straight TX20 03073256-xx

T12 Hexagon socket head cap screwdriver 0.7 - 2 00320265-xx

T13 Double wrenches size 17 x 19 03109304-xx

T19 Wire cutter electronic size 110 00318673-xx

T22 Multipette M4 00386154-xx