A700000009046784.pdf - 第16页

16 Packing l ist MPP1 - PICK & PLACE M ANIP ULA TOR version 2.4 Serial number : ........................ ......... Standard delivery Volume Packed Assembling desk MPP1 with m ovable armrest and assembling head with i…

Work with the Manipulator

The manipulator MPP1 was developed for manual assembling of SMD components. With different

types of feeders it is possible to assemble SMD components from strips but also from IC sticks.

Before switching on the manipulator, check that all cables are connected correctly and that the

vacuum hose is connected to both the vacuum pump and to the manipulator. Ground the

manipulator with an ESD cable (included). Plug the monitor, vacuum pump and adapter into an

electrical outlet (AC 230 V). If all cables are connected and the vacuum pump is switched on, you

can switch on the manipulator with the main button on the right. The button lights up and the camera

view appears on the screen within 3 - 5 seconds. If the preview does not appear, check that all cables

are connected properly.

Do not disconnect any cables, disconnect the adapter or the vacuum pump from the socket when

the manipulator is switched on! Place the feeders on the assembling desk as described.

Assembling

Attach the needle to the conical shaft - put it gently so that it can be easily removed. For small

components (0201, 0402) use a thinner pink needle, for larger components (603, 1206, SO8, SO16

etc.) a thicker brown needle. Use a rubber suction cup to fit larger integrated circuits or the processors.

Slide the rubber suction cup onto the assembling needle so that the end of the assembling needle

stayed inside the suction cup. Place the required number of assembled PCBs on the PCB holders.

Place your left hand on the left

armrest, your right hand put on the

movable armrest and grasp the

assembling head with your palm. The

thumb controls the rotation of the

knob (ie the component) as well as the

vertical movement of the assembling

needle. The conical shaft of the needle

has a free movement in the range of 4-

5 mm, which is used to turn the

vacuum on and off.

Move the assembling head over the

component, carefully bring the end of

the needle closer to the component

surface and lightly touch it. This sucks

the component to the end of the

needle. When the needle touched the

component and the component is sucked, stop the downward movement of the button. Gently release

the button to return to its primary upper position. Move to the desired position, turn the knob to direct

the component correctly and press down the knob to place the component on the PCB.

When the mounting head is pushed to the lowest position, the vacuum is switched off (reduced to a

minimum) and the part remains stuck in the paste. When we release the head and the spring pushes it

to the highest position, the vacuum is switched on again (increased to the maximum).

Small parts adhere to the paste without reducing the vacuum.

Always switch-off the manipulator with the main button! After switching off the manipulator

(using the main button), you can disconnect the monitor, adapter and vacuum pump from the

socket.

Maintenance

The manipulator does not require special maintenance. Make sure that the round rod of movable

armrest is neither covered in dust nor messed with various impurities. It must be kept lightly oiled.

Larger impurities (metal or wood sawdust etc.) can damage linear bearing. The assembling needle

must be cleaned from solder paste after work, because later cleaning can be problematic if the paste

dries up.

The assembling head is maintenance-free, no further lubrication is required. Improper intervention can

damage the assembling head, e.g. non-linear movement may occur or excessive oiling can leak and

degrade the PCB.

Always keep the feeders dust-free and it is recommended that you clean the sliders from dust before

use to prevent them from sticking to the IC´s pins.

Service

In case of manipulator failure, please contact the dealer or the device manufacturer. Only original

spare parts available from the manufacturer must be used for repair. Do not repair in any case the

manipulator yourself.

Disposal

Dispose of the packaging in an environmentally friendly manner. It is made of ecological materials,

which can either be recycled or disposed of in local waste recycling site.

Do not dispose of electrical tools in the municipal waste. Dispose of electronic tools in accordance

with European directive no. 2012/19/EU, which states that worn out electronic tools and devices must

be collected separately and handed in for ecological recycling.

To get more information about disposal of worn out electronic devices, please inquire at the relevant

public administration body.

We reserve the right to make any changes in the operating manual of the device.

Packing list

MPP1 - PICK & PLACE MANIPULATOR

version 2.4

Serial number: .................................

Standard delivery Volume Packed

Assembling desk MPP1 with movable armrest and

assembling head with integrated CCD camera

1 pc

PCB holder

3 pcs

Storage box

1 pc

Assembling needle NEED1, brown

1 pc

Assembling needle NEED2, pink

1 pc

Rubber suction cup dia 3.5 mm

1 pc

Rubber suction cup dia 6.4 mm

1 pc

Vacuum pump with the control valve and hose (1m)

1 pc

ESD cable with crocodile clip

1 pc

Adapter 230 V / 12 V 1 pc

PC monitor (HDMI cable, power cord)

1 pc

Operating manual

1 pc

Warranty

1 pc

Optional accessories Volume Packed

Tape feeder

Tape feeder combined

Reel holder

Reel holde combined

IC feeder

Assembling needle (code )

Rubber suction cup (code )

Dispensing head

PCB holder

Dispenser (code )

Other:

Date

Packed by

Checked by