DECAN_S1_Maintenance(Eng_Ver1.1)_Print.pdf - 第16页

chapt er 1 This Chapter describes the work environment and working tools for the maintenance of the machine. Conditions fo r Main t e nanc e Nex t Generation, Multi- Functi onal Placer DE CAN S1 M ain ten anc e Ha nd boo…

100%1 / 84
chapter 1
This Chapter describes the work environment and working tools for the maintenance of
the machine.
Conditions for Maintenance
Next Generation, Multi-Functional Placer
DECAN S1 Maintenance Handbook
1-6
Common Working Procedure before Maintenance
Conditions for Maintenance
3. Releasing 'Emergency Stop' mode
Step 1.
Press the 'EMG' button
Step 2.
Press the 'STOP' button
Step 3.
Press the 'RESET' button
Step 4.
Press the 'READY' button
Warning
Perform checking with the power supply to the motor cut off
without fail.
chapter 1
This Chapter describes the work environment and working tools for the maintenance of
the machine.
Conditions for Maintenance
Next Generation, Multi-Functional Placer
DECAN S1 Maintenance Handbook
1-7
Working Environment and Condition
Requirements for air pressure
DEF. DESCRIPTION
Primary pressure 5.0 - 7.0 kgf/cm
2
Secondary pressure 4.5 - 5.5 kgf/cm
2
Air Consumption Vacuum Pump: 50 NL/min
Environmental conditions
DEF. DESCRIPTION
During
operation
Temperature 10℃-35℃(Recommended:20℃-28℃)
Humidity
30 % - 80 % RH (non-condensation state)
Lessthan70%RH(Morethan30℃,non-
condensation state)
During
shipment or
storage (in
states other
than during
operation)
Temperature -10℃-60℃
Humidity
10 % RH - 90 % RH (non-condensation state)
Morethan35℃(Lessthawet-bulbtemperature
35℃,non-condensationstate)
Power requirements
DEF. DESCRIPTION Notes
Capacity 3.5 kVA
Frequency 50/60Hz
Phase 3 Phase
Connection Y-Y
Rated Primary Voltage AC 200 V ±10 %
AC 208 V ±10 %
AC 220 V ±10 %
AC 240 V ±10 %
AC 380 V ±10 %
AC 415 V ±10 %
Permitted Voltage
Drop(s)
Short Circuit Current Rating 50 KA (220 VAC)
Distribution System TN
Full-Load Current 13 A Full Load Ampere
Peak Starting Currents -
Warning
If unspecified voltage is used or power input is changed
improperly, fire could occur and a death from electric shock could
occur.
Change of power input must be done by a trained repair and
maintenance operator or our authorized C/S personnel.
Working Environment and Condition
chapter 1
This Chapter describes the work environment and working tools for the maintenance of
the machine.
Conditions for Maintenance
Next Generation, Multi-Functional Placer
DECAN S1 Maintenance Handbook
1-8
Working Environment and Condition
Conditions for Maintenance
Installation requirements
DEF. DESCRIPTION Notes
Height 900 ± 20 mm or
952.5 ± 12.5 mm
ㆍ Based on the top of the
PCB transfer belt
Leveling Simultaneous measurement at
3 locations
ㆍ Level gauge graduation
Right and left Deviation 0.05
mm/M within graduation
ㆍ Y1 LM Guide Top Center
ㆍ Y2 LM Guide Top Center
ㆍ Front FeederBase Center
Cooling
system
Secure space in front of the
cooling fan
ㆍ 2 places in the upper
center
ㆍ 1 place each at the lower
front and back sides
ㆍ 1 place at the bottom of
the right side