A10011-ASM-T46-EN-Spec-SX-V2_DMS.pdf - 第16页

16 Placement heads SIPLACE TwinStar (TH) SIPLACE TwinStar (TH) With component camer a type 33 (fine pitch camer a) With component c amera type 25 (flip chip camer a) Component range a a) Please note that the placeable co…

100%1 / 64
15
Placement heads
SIPLACE MultiStar (CPP)
SIPLACE MultiStar (CPP)
With component camera
type 30
With component camera type 33
(stationary camera)
Component range
a
a) Please note that the placeable component range is also affected by the pad geometry, the customer-spe-
cific standards, the component packaging tolerances and the component tolerances.
01005 to 27 mm x 27 mm 0402 to 50 mm x 40 mm
b
b) A diagonal of 69 mm is possible during multiple measurements (e.g. 64 mm x 10 mm).
Component spec.
Max height
c
Max. height
d
Min. lead pitch
Min. lead width
Min. ball pitch
Min. ball diameter
Min. dimensions
Max. dimensions
Max. weight
c) CPP head: in low installation position (stationary component camera not possible).
d) CPP head: In high installation position
6.0 mm
8.5 mm
250 µm
100 µm
e
/ 200 µm
f
250 µm
e
/ 350 µm
f
140 µm
e
/ 200 µm
f
0.4 mm x 0.2 mm
27 mm x 27 mm
4 g
g
e) For components < 18 mm x 18 mm.
f) For components ≥ 18 mm x18 mm.
g) 20 g in „Pick&Place“ mode
11.5 mm / 15.5 mm
h
300 µm
150 µm
350 µm
200 µm
1.0 mm x 0.5 mm
50 mm x 40 mm
8 g
g
Set-down force 1.0 - 15 N
h
h) With OSC package
Nozzle types 20xx, 28xx 20xx, 28xx
X/Y accuracy
i
i) The accuracy values fulfill the conditions in the SIPLACE scope of supply and services.
± 38 µm/3 ± 30 µm/3
Angular accuracy ± 0.20° / 3
j
, ± 0.38° / 3
k
j) Component dimensions between 6 mm x 6 mm and 27 mm x 27 mm.
k) Component dimensions smaller than 6 mm x 6 mm.
± 0.12° / 3
Illumination levels 5 6
16
Placement heads
SIPLACE TwinStar (TH)
SIPLACE TwinStar (TH)
With component camera type 33
(fine pitch camera)
With component camera type 25
(flip chip camera)
Component range
a
a) Please note that the placeable component range is also affected by the pad geometry, the customer-specific standards, the
component packaging tolerances and the component tolerances.
0402 to SO, PLCC, QFP, BGA, special
components, bare dies, flip-chips
0201 to SO, PLCC, QFP, sockets, plugs,
BGA, special components, bare dies, flip-
chips, shields
Component specs
Max. height
Min. lead pitch
Min. lead width
Min. ball pitch
Min. ball diameter
Min. dimensions
Max. dimensions
Max. weight
b
b) Component plus nozzle or gripper.
25 mm / 50 mm
c
300 µm
150 µm
350 µm
200 µm
1.0 mm x 0.5 mm
55 mm x 45 mm (single measurement)
Up to
200 mm x 125 mm (multiple measurement)
d
100 g to 240 g
e
c) Only with SIPLACE Very High Force Twin Star (VHF TH)
d) Further restrictions will apply, according to the component dimensions and the component supply. These will be automati-
cally taken into account by SIPLACE Pro.
e) Up to 100 g is standard. Over 100 g available with reduced acceleration. From 160 g only with SIPLACE Very High Force
Twin Star (VHF TH)
25 mm / 40 mm
c
250 µm
100 µm
140 µm
80 µm
0.6 mm x 0.3 mm
16 mm x 16 mm (single measurement)
Up to
55 mm x 55 mm (multiple measurement)
d
100 g to 240 g
e
Set-down force 1.0 N - 15 N
1.0 N - 30 N with OSC package
2.0 N - 70 N
c
2.0 N -100 N
f
f) Only with SIPLACE Very High Force Twin Star (VHF TH) and OSC package
1.0 N - 15 N
1.0 N - 30 N with OSC package
2.0 N - 70 N
c
2.0 N -100 N
f
Nozzle types
g
g) Over 300 different nozzles and 100 gripper types are available, with an extensive nozzle database available online.
5xx (standard)
20xx/28xx + adapter
4xx + adapter
9xx + adapter
Gripper
5xx (standard)
20xx/28xx + adapter
4xx + adapter
9xx + adapter
Gripper
Nozzle spacing for P&P
heads
70.8 mm 70.8 mm
X/Y accuracy
h
h) The accuracy values fulfill the conditions in the SIPLACE scope of supply and services.
± 26 µm/3 ± 22 µm/3
Angular accuracy ± 0.05° / 3 ± 0.05° / 3
Illumination levels 6 6
17
Placement heads
Nozzle changer
Nozzle changer for the SIPLACE SpeedStar (C&P20 P)
Nozzle changer for the SIPLACE MultiStar CPP
Nozzle changer for the SIPLACE TwinStar
Magazine for 20 nozzles of
type 40xx
Magazine for 9 nozzles of
type 28xx
Magazine for 20 nozzles of type 20xx
Description
Nozzle changers increase the flexibility of the placement heads when it comes to processing
different components. The nozzle configuration can be rapidly adjusted to changing place-
ment jobs. Precisely defined positions and perfect nozzle seat in the garage ensure minimum
radial eccentricity on the placement head.
The nozzle changers feature a monitoring circuit. This checks whether the nozzle magazines
are seated correctly on the mount. In addition, the nozzle changers recognize whether the
magazines are for 10xx, 20xx or 28xx nozzles by the code.