YG12F_Ope_E.pdf - 第33页
iv About this manual 3. Page layout The description below shows a typical page layout used in this manual. 3-8 3 Starting and ending production 2. Ending production and turning power of f Use the following procedure to e…
iii
About this manual
2. Contents of each chapter
This manual is comprised of the following chapters.
Safety instructions
This section provides safety instructions essential when using the machine.
About this manual
Chapter 1 Part names and functions
Explains major part names and functions of the machine that you should know before attempting operation.
Chapter 2 Basic operation
• Explains how to use buttons and on-screen menus for machine operation.
• Explains the basic operation for board production including the conveyor unit setups.
• Explains the procedure from how to start up the machine to how to turn it off.
• Shows typical errors and troubleshooting.
Chapter 3 Starting and ending production
Describes the procedure from production start to end, as well as the contents of the production monitor that can be
displayed during operation.
Appendix
Contains machine specifications.
Index
The index at the end of this manual helps you quickly find where necessary items are explained.
iv
About this manual
3. Page layout
The description below shows a typical page layout used in this manual.
3-8
3
Starting and ending production
2. Ending production and turning power off
Use the following procedure to end board production.
Stop machine operation.
There are four methods for stopping the machine operation.
1. Emergency stop button:
Press this button to trigger emergency stop. Do not use this button in normal operation.
2. [STOP] button (operation panel):
Pressing the [STOP] button stops the machine operation immediately. To resume operation, press the
[STAR T] button on the operation panel.
3. [Cycle Stop] button (operation screen):
Pressing this button stops the machine operation just after components are mounted on the current
board.
4. [Convey-out stop] button (operation screen):
Use this button when you want to end production after completing component mounting on the
boards currently on the conveyor. All boards on the conveyor are carried out after component
mounting, but new boards are not carried in from the upstream side.
CAUTION
Do not press the emergency stop button during operation except in case of emergency.
Reset the operation.
Press the [RESET] button on the operation panel. The machine then returns to the board production
standby status.
Press the [Off] button.
Press the [Off] button in the left button area of the screen.
[Off] button
[Off] button
24306-L6-00
Typical page layout
Step
Chapter number
Chapter title
Substep or
description of step
Figure, picture
or table caption
Note, Caution
or Warning
23001-M7-00
n
Step
This describes the procedure for each operation.
n
Substep or description of step
This provides detailed information on the steps in the procedure.
n
Figure or table caption
This is the title of the figure or table and appears at the upper left.
n
Note, Caution or Warning
These are explained in detail in "Safety instructions".
Chapter 1 Part names and functions
Contents
1
3
2.1 Keyboard and mouse 1-3
4
3. Head assembly 1-5
3.1 Component pick-and-place head 1-6
3.1.1 5-in-line multi-head assembly 1-6
3.1.2 Multi-vision camera 1-6
3.2 Nozzle types 1-7
3.2.1 Nozzles for the 5-in-line head assemblies 1-7
3.3 Nozzle station (option) 1-9
4. Component supply section 1-11
4.1 Supplying components from feeder plates 1-11
4.1.1 Fixed 24-feeder plate 1-11
4.2 Supplying components from tray changer (ATS15) 1-12
4.2.1 ATS15 main unit 1-12
4.2.2 Pallet 1-13
5.
Conveyor unit and component recognition system
1-15
6. Axis configuration 1-16
7
7
7.1.1 Performing a nozzle shaft blow 1-18
3