Vakuumtooling an HS60.pdf - 第31页

SOKO 1 Montageanleitung SOKO Vakuum-Tooling SIPLACE HS-60 Ausgabe 10/2006 31 1.1 1 Einbau der Abdeckung fü r die Laserlicht schranke (Option) Für sehr dünne Leiterplatte n (< 0,3mm) ist der S tra hl des Lasers zu sehr…

100%1 / 62
1 Montageanleitung SOKO Vakuum-Tooling SIPLACE HS-60 SOKO
Ausgabe 10/2006
30
24, 0, // no verification of clamping with motor 1
41, 0, // left side fixed, width adjustment 1
43, 0, // fixed rails pitch (actual) 1
44, 0, // fixed rails pitch (target) 1
42, 0, // extendend region width adjustment 1
48, 100, // [%] force stepping motor width adj. 1
49, -413, // [um] offset width adjustment 1
50, -969, // [um] offset fixed rail 1
47, 1, // position fixed rail ok 1
60, 855, // [um] calibration position 1, width adj. 1
61, 48315, // [um] calibration position 2, width adj. 1
62, 220, // [um] cavity driver, input, width adj. 1
63, -39, // corr. a0, sensor width adj., input 1
64, 42, // corr. a1, sensor width adj., input 1
65, 48, // corr. a2, sensor width adj., input 1
66, 207, // [um] cavity driver, output, width adj. 1
67, -11, // corr. a0, sensor width adj., output 1
68, -27, // corr. a1, sensor width adj., output 1
69, -2, // corr. a2, sensor width adj., output 1
70, 0, // [um] cavity driver, middle, width adj. 1
71, 0, // corr. a0, sensor width adj., middle 1
72, 0, // corr. a1, sensor width adj., middle 1
73, 0, // corr. a2, sensor width adj., middle 1
80, 60, // [mm/s] velocity stopper 1
81, 350, // [mm/s] velocity sensor stopper 1
82, 25, // [0.1m/s²] deceleration stopper 1
83, 600, // [ms] drive-up time stopper 1
84, 60, // [mm/s] velocity stopper LBO 1
85, 300, // [mm/s] velocity sensor LBO 1
86, 25, // [0.1m/s²] deceleration stopper LBO 1
87, 600, // [ms] drive-up time stopper LBO 1
1
1
1
1
1
1
1
SOKO 1 Montageanleitung SOKO Vakuum-Tooling SIPLACE HS-60
Ausgabe 10/2006
31
1.11 Einbau der Abdeckung für die Laserlichtschranke
(Option)
Für sehr dünne Leiterplatten (< 0,3mm) ist der Strahl des Lasers zu sehr gestreut und die Leiter-
platte wird nicht erkannt. Mit der Abdeckung wird dieses verbessert. 1
1
1
: Entfernen Sie die beiden Schrauben mit denen die Lichtschranke befestigt ist und nehmen Sie
die Lichtschranke heraus.
1
Abdeckung
Laserlichtschranke
1 Montageanleitung SOKO Vakuum-Tooling SIPLACE HS-60 SOKO
Ausgabe 10/2006
32
: Legen Sie die Abdeckung wie auf dem unteren Bild zusehen auf die Laserlichtschranke und
schrauben Sie die Lichtschranke wieder mit den beiden Schrauben fest.
1
1
1
1
Laserlichtschranke
Abdeckung