Nordson_EFD_Automated_Dispensing_Systems_Maintenance_Guide.pdf - 第10页

Automated Dispensing Systems Maintenance & Parts Guide 10 www.nordsonefd.com info@nordsonefd.com +1-401-431-7000 Sales and service of Nordson EFD dispensing systems are available worldwide. R / RV Series Ball Screw C…

100%1 / 42
9www.nordsonefd.com info@nordsonefd.com +1-401-431-7000 Sales and service of Nordson EFD dispensing systems are available worldwide.
Automated Dispensing Systems Maintenance & Parts Guide
Linear Guideway Cleaning: ZAxis (continued)
Clean and Grease the ZAxis Linear Guideway (continued)
3
(E2/E2V Series only)
Clean the Zaxis as follows:
a. Use a clean nonwoven cloth to clean any
dust and grease from the Zaxis linear
guideway.
b. Move the Zaxis head down to clean
previously inaccessible areas of the Zaxis
linear guideway.
c. Use the brush and grease from the
maintenance grease kit to liberally apply
grease to the Zaxis linear guideway.
Move the Zaxis module up and down to
spread the grease evenly and to ensure the
slide travels smoothly on the Zaxis linear
guideway.
d. If the Zaxis module does not travel easily,
add grease to the grease fitting on the Zaxis
linear guideway. Refer to “Applying Grease
to the Grease Fittings” on page12 for
instructions. Return here to continue.
ba
ZAxis
linear
guideway
c
Reinstall the ZAxis Cover (All Units Except R / RV Series)
4
a. Reinstall the Zaxis cover.
b. Secure the cover with the screws removed
previously.
b
a
b
Automated Dispensing Systems Maintenance & Parts Guide
10 www.nordsonefd.com info@nordsonefd.com +1-401-431-7000 Sales and service of Nordson EFD dispensing systems are available worldwide.
R / RV Series Ball Screw Cleaning: Z and R Axes
NOTE: This procedure applies only to R / RV Series units.
CAUTION
Risk of injury or equipment damage. Before performing any service procedure, complete the steps under
“Preparation for all Service Procedures” on page3.
Remove the ZAxis Cover (R / RV Series Only)
1
a. Remove the 10 screws that secure the
Zaxis cover to the Zaxis module.
b. Carefully pull up vertically to remove the
Zaxis cover.
NOTE: Removing the four (4) screws near
the bottom of the Zaxis cover releases
the Zaxis bottom plate; place your hand
underneath the plate to catch it.
NOTE: The Zaxis module can be in
any position along the Xaxis during
maintenance.
ba
Clean and Grease the ZAxis Components (R / RV Series Only)
2
Clean the Zaxis as follows:
a. Use a clean nonwoven cloth to clean any
dust and grease from the Zaxis ball screw,
spring, spring shaft, and Raxis ball spline.
b. Pull the Zaxis head down, exposing
all components listed above that were
previously inaccessible, and clean the dust
and grease with the nonwoven cloth.
NOTE: Keep the Zaxis head in the down
position.
c. Use the brush and grease from the
maintenance grease kit to liberally apply
grease to the Zaxis ball screw, spring,
spring shaft, and Raxis ball spline.
d. After greasing, release the Zaxis head from
the down position and move the Zaxis
module up and down to disperse the grease
evenly on each component.
e. Use a clean nonwoven cloth to remove
excess grease.
Raxis ball
spline
Spring on
spring shaft
Zaxis
ball screw
c
Continued on next page
11www.nordsonefd.com info@nordsonefd.com +1-401-431-7000 Sales and service of Nordson EFD dispensing systems are available worldwide.
Automated Dispensing Systems Maintenance & Parts Guide
Linear Guideway Cleaning: Z and R Axes (continued)
Clean and Grease the RAxis Components
3
Clean the Raxis as follows:
a. Use a clean nonwoven cloth to clean any
dust and grease from the rotational ball
screw and rotational shafts.
b. Rotate the Raxis multiple times to expose
the parts of the rotational ball screw and
rotational shafts previously inaccessible
and clean the grease and dust with the
nonwoven cloth.
NOTE: Keep the Raxis in the rotated
position.
c. Use the brush and grease from the
maintenance grease kit to liberally apply
grease to the rotational ball screw and
rotational shafts.
d. After greasing, release the Raxis from the
rotated position and then rotate the Raxis
clockwise and counterclockwise to disperse
the grease evenly on the two components.
e. Use a clean nonwoven cloth to remove
excess grease.
c
Rotational
ball screw
Rotational
shafts
a
Reinstall the ZAxis Cover (R / RV Series Only)
4
a. Position the Zaxis cover over the Zaxis
module and vertically lower it to its correct
orientation.
b. Lift up the Zaxis bottom plate and secure
the two components with the 10 screws
removed previously.
ba