Nordson_EFD_Automated_Dispensing_Systems_Maintenance_Guide.pdf - 第35页

35 www.nordsonefd.com info@nordsonefd.com +1-401-431-7000 Sales and service of Nordson EFD dispensing systems are available worldwide. Automated Dispensing Systems Maintenance & Parts Guide Fuse Replacement CAUTION R…

100%1 / 42
Automated Dispensing Systems Maintenance & Parts Guide
34 www.nordsonefd.com info@nordsonefd.com +1-401-431-7000 Sales and service of Nordson EFD dispensing systems are available worldwide.
ZAxis Spring Replacement (E and EV Series Only)
CAUTION
Risk of injury or equipment damage. Before performing any service procedure, complete the steps under
“Preparation for all Service Procedures” on page3.
1
a. Remove the four (4) screws that secure the
Zaxis cover to the Zaxis module.
b. Pull up vertically to remove the Zaxis cover.
a
b
a
2
While keeping the Zaxis head in the top
position, grasp the bottom of the Zaxis spring
and then pull it down and push it towards the
back of the robot to release it from the retaining
lip.
Z axis
spring
3
Remove the screw that secures the Zaxis
spring; this frees the spring.
Z axis spring
screw
4
Secure the replacement Zaxis spring with the screw removed previously.
5
Grasp the bottom of the Zaxis spring and then pull it down and place the bottom loop inside the
retaining lip.
6
a. Reinstall the Zaxis cover.
b. Secure the cover with the screws removed
previously.
b
a
b
35www.nordsonefd.com info@nordsonefd.com +1-401-431-7000 Sales and service of Nordson EFD dispensing systems are available worldwide.
Automated Dispensing Systems Maintenance & Parts Guide
Fuse Replacement
CAUTION
Risk of injury or equipment damage. Before performing any service procedure, complete the steps under
“Preparation for all Service Procedures” on page3.
Fuse Replacement (P/N 7361392 — All Units Except E2) (P/N 7361391 — E2 Units)
1
Unscrew the robot fuse holder (P/N 7361394)
and remove the fuse.
NOTE: The fuse is located on the left side of the
control assembly cover on all models except
E2 units. On E2 units, the fuse is located on the
right side of the control assembly cover.
E2 fuse
location
Fuse location for all
units except E2
Robot fuse
holder
2
Visually inspect the fuse for a broken wire or
a scorched cylinder that is brown or black in
color; these are signs of a blown fuse.
NOTE: You can also use a multimeter to check
the fuse: With the multimeter in resistance
mode, touch the metal tips of the testing leads
to the metal ends of the fuse. If the resistance
displayed does not change (thus remaining at a
100% resistance state), then the fuse is blown.
If a small resistance is measured, then the fuse
is good.
3
(All units except E2)
If the fuse is blown, remove it from the robot fuse holder install a new 20 mm, 3 A fuse (P/N7361392).
(E2 units only)
If the fuse is blown, remove it from the robot fuse holder install a new 20 mm, 1 A fuse (P/N7361391).
4
Reinstall the robot fuse holder in the robot.
Automated Dispensing Systems Maintenance & Parts Guide
36 www.nordsonefd.com info@nordsonefd.com +1-401-431-7000 Sales and service of Nordson EFD dispensing systems are available worldwide.
Fuse Replacement (P/N 7361393 — All Units Except E2)
1
Open the fuse release latch located between
the Power Switch and the Power Inlet. The latch
has a fuse symbol on it.
Fuse release
latch
2
Pull open the spare‑fuse holder.
NOTE: The spare‑fuse holder includes two
fuses. The fuse closest to the exterior face is in
storage and the far side fuse is in use.
Top view
Bottom
view
Stored
fuse
Fuse in
use
3
Visually inspect the fuse for a broken wire or a scorched cylinder that is brown or black in color; these
are signs of a blown fuse.
NOTE: You can also use a multimeter to check the fuse: With the multimeter in resistance mode, touch
the metal tips of the testing leads to the metal ends of the fuse. If the resistance displayed does not
change (thus remaining at a 100% resistance state), then the fuse is blown. If a small resistance is
measured, then the fuse is good.
4
Remove the blown fuse from the spare fuse holder and install a new fuse.
5
Reinstall the spare fuse holder with the new fuse in the power socket.
Fuse Replacement (continued)
I/O Microfuse Replacement
1
Remove the control assembly. Refer to the
applicable steps under “Remove and Clean the
Control Assembly” on page14 to remove the
control assembly. Return here to continue.
Continued on next page