ERR-LIST-ACM.pdf - 第7页
523 Transport :\tCommunication error work-area Communication error occurred inside the transport controller. - Wrong parameters sent to servo controller; this error should not occur. - Retry and continue. - Restart the s…
511
Transport :\tCommunication time-
out run-out
The servo system of the transport
run-out section reacts too slow. - Transport controller hardware error.
- Retry and continue.
- Restart the system.
- Report error to your service representative.
512
Transport :\tCommunication error
run-out
Communication error occurred
inside the transport controller.
- Wrong parameters sent to servo controller; this error should
not occur.
- Retry and continue.
- Restart the system
- Report error to your service representative.
513 Transport :\tposition error width
The servo system of the transport
width is not able to move to the
requested position.
- The requested position is outside the mechanical range.
- The friction of the width mechanics is too high.
- The servo system is defect.
- Retry and continue.
- Restart the system.
- Contact your service representative.
514 Transport :\ttracking warning width
The width servo system has
detected a position failure. - The friction of the width mechanics is increasing.
- Maintenance is required.
- Retry and continue.
- Restart the system.
515
Transport :\tHome width position
lost.
An attempt was made to adjust the
transport width, while the transport
width was not calibrated.
(Width calibration is automatically
initiated by the system, prior to
width adjustments.)
- An attempt to home the width failed (no servo power, or
boards presented in the machine).
- Hardware failure.
- Internal error.
- Enter the dialogue machine set-up : user is prompted for width homing.
- Activate run-out and start the machine.
- Retry the operation
516
Transport :\tCommunication time-
out width
The servo system of the transport
width reacts too slow. - Hardware error on transport controller.
- Retry and continue.
- Restart the system.
- Report error to your service representative.
517
Transport :\tCommunication error
width.
Communication error occurred
inside the transport controller.
- Wrong parameters sent to servo controller; this error should
not occur.
- Retry and continue.
- Restart the system
- Report error to your service representative.
518
Transport :\tUnable to calibrate
width
During width homing the zero
coarse sensor (EPD) could not be
located.
- EPD defective
- EPD wiring malfunction.
- Width hardware failure.
- Retry and continue.
- Restart the system.
- Contact your service representative.
519
Transport :\ttimeout occurred
during width calibration
The width calibration has a time-
out. Width calibration is
automatically initiated when
needed, i.e. transport width is set
and the transport width servo
system has never been calibrated
before. - The movement class for transport width calibration is too slow. - Adjust the movement class for transport width calibration.
520
Transport :\tposition error work-
area
The servo system of the transport
work-area is not able to move to
the requested position.
- Transport belt in work-area is jammed.
- The friction of the transport mechanics is too high
- The servo system is defect.
- Check transport mechanics for being jammed.
- Maintenance or repair is required.
- Contact your service representative.
521
Transport :\ttracking warning work-
area
The work-area servo system has
detected a position failure. - The friction of the work-area mechanics is increasing - Maintenance is required.
522
Transport :\tCommunication time-
out work-area
The servo system of the transport
work-area section reacts too slow. - Transport controller hardware error.
- Retry and continue.
- Restart the system.
- Report error to your service representative.
523
Transport :\tCommunication error
work-area
Communication error occurred
inside the transport controller.
- Wrong parameters sent to servo controller; this error should
not occur.
- Retry and continue.
- Restart the system.
- Report error to your service representative.
524 Transport :\tposition error run-in
The servo system of the transport
run-in is not able to move to the
requested position
- Run-in belt jammed.
- The friction of the run-in mechanics is too high.
- The servo system is defect.
- Check run-in mechanics for being jammed.
- Maintenance or repair is required.
- Contact your service representative.
525
Transport :\ttracking warning run-
in
The run-in servo system has
detected a position failure. - The friction of the run-in mechanics is increasing - Maintenance is required.
526
Transport :\tcommunication time-
out run-in
The servo system of the transport
run-in section reacts too slow. - Transport controller hardware error.
- Retry and continue.
- Restart the system.
- Report error to your service representative.
527
Transport :\tCommunication error
run-in
Communication error occurred
inside the transport controller.
- Wrong parameters sent to servo controller; this error should
not occur.
- Retry and continue.
- Restart the system.
- Report error to your service representative.
528
Transport :\tamplifier lift/width
disabled.
The amplifier of the lift/ width servo
system is disabled. - Software error.
- Retry and continue.
- Restart the system.
- Report error to your service representative.
529
Transport :\tamplifier run-in/work-
area disabled.
The amplifier of the servo system
of the run-in/work-area section is
disabled. - Software error.
- Retry and continue.
- Restart the system.
- Report error to your service representative.
530
Transport :\tamplifier run-out
section disabled.
The amplifier of the run-out servo
system is disabled. - Software error.
- Retry and continue.
- Restart the system.
- Report error to your service representative.
531 Transport :\tZero drift run-in
The servo system of the run-in has
detected, that the zero-index has
changed.
- Disruption on the servo wiring.
- Encoder error.
- Hardware error.
- Check/exchange wiring.
- Check/exchange motor-encoder combination.
- Check/exchange transport controller.
532 Transport :\tZero drift work-area
The servo system of the work-area
has detected that the zero-index
has changed.
- Disruption on the servo wiring.
- Encoder error.
- Hardware error.
- Check/exchange wiring.
- Check/exchange motor-encoder combination.
- Check/exchange transport controller.
533 Transport :\tZero drift width
The servo system of the width has
detected that the zero-index has
changed.
- Disruption on the servo wiring.
- Encoder error.
- Hardware error.
- Check/exchange wiring.
- Check/exchange motor-encoder combination.
- Check/exchange transport controller.
534 Transport :\tZero drift lift
The servo system of the lift has
detected, that there is a mismatch
between the calibrated value and
the physical value.
- Disruption on the servo wiring.
- Encoder error.
- Hardware error.
- Check/exchange wiring.
- Check/exchange motor-encoder combination.
- Check/exchange transport controller.
535 Transport :\tZero drift run-out
The servo system of the run-out
has detected that the zero-index
has changed.
- Disruption on the servo wiring.
- Encoder error.
- Hardware error.
- Check/exchange wiring.
- Check/exchange motor-encoder combination.
- Check/exchange transport controller.
536 Transport :\tposition error lift
The servo system of the transport
lift is not able to move to the
requested position, or the servo
system has detected a position
failure, which exceeds the error
limit.
- The requested position is outside the mechanical range.
- The friction of the lift mechanics is too high.
- The servo system is defective. - Maintenance is required in case of a friction problem.
537
Boards are present in the
machine.
An operation was requested for
which no boards may be present
in the machine, e.g. transport
width jogging.
- One or more boards are present in the machine.
- If this is not the case a mismatch exist between the physical
and reported board positions. - Select activate run-out and start the production and retry the operation.
538
Transport :\timpact point lift not
found
The transport was not able to
detect the impact point during lift
calibration
- Hardware error.
- Friction in lift movement
- Parameter window too small.
- Check hardware.
- Retry and continue.
- Restart the system
- Contact your service representative.
539 Transport :\tNo servo power
An attempt was made to start the
transport while no servo power
was available on the transport
controller board.
- Servo power is not switched on.
- Servo power fuse is damaged.
- Other modules caused that the emergency circuit is enabled.
- Switch on servo power, when not able to switch on then.
- Check position H-drive, it may be in the end-position.
- Check covers ( maybe not closed) and check emergency buttons (front/rear),
may be activated.
- Check power fuse, if broken then replace
540 Transport :\tparameter error
Parameter error reported by the
transport controller. - Software error.
- Retry and continue.
- Restart the system.
- Report error to your service representative.
541 Transport :\tPower dip detected
A power dip was detected on the
power supply of the transport
controller. - Defective power supply. - Check power supply.
542
Transport :\temergency input
active
This error message is obsolete
and should not occur - Report error to your service representative.
543
Transport :\temergency output
active
This error message is obsolete
and should not occur - Report error to your service representative.
544 Transport :\tFlash PROM full
The flash PROM on the transport
controller board is full. - Purge flash PROM.
545
Transport :\tFlash PROM write
error
The flash PROM on the transport
controller board has one or more
locations which can not be written.
- The flash PROM is write protected.
- The flash PROM is defective.
- Put jumper X44 on the transport controller board.
- Exchange transport controller.
546
Transport :\tFlash prom erase
error
The flash PROM has one or more
location which can not be erased.
This is an error in the flash PROM on the transport controller
board. - Exchange transport controller.