ERR-LIST-ACM.pdf - 第9页
547 Transport :\twrong flash ID Flash PROM is write protected. - The flash prom on the controller is of the wrong type. - No jumper X44 is installed on the controller card. - Replace with correct type: 28F256 (Intel 89B9…
535 Transport :\tZero drift run-out
The servo system of the run-out
has detected that the zero-index
has changed.
- Disruption on the servo wiring.
- Encoder error.
- Hardware error.
- Check/exchange wiring.
- Check/exchange motor-encoder combination.
- Check/exchange transport controller.
536 Transport :\tposition error lift
The servo system of the transport
lift is not able to move to the
requested position, or the servo
system has detected a position
failure, which exceeds the error
limit.
- The requested position is outside the mechanical range.
- The friction of the lift mechanics is too high.
- The servo system is defective. - Maintenance is required in case of a friction problem.
537
Boards are present in the
machine.
An operation was requested for
which no boards may be present
in the machine, e.g. transport
width jogging.
- One or more boards are present in the machine.
- If this is not the case a mismatch exist between the physical
and reported board positions. - Select activate run-out and start the production and retry the operation.
538
Transport :\timpact point lift not
found
The transport was not able to
detect the impact point during lift
calibration
- Hardware error.
- Friction in lift movement
- Parameter window too small.
- Check hardware.
- Retry and continue.
- Restart the system
- Contact your service representative.
539 Transport :\tNo servo power
An attempt was made to start the
transport while no servo power
was available on the transport
controller board.
- Servo power is not switched on.
- Servo power fuse is damaged.
- Other modules caused that the emergency circuit is enabled.
- Switch on servo power, when not able to switch on then.
- Check position H-drive, it may be in the end-position.
- Check covers ( maybe not closed) and check emergency buttons (front/rear),
may be activated.
- Check power fuse, if broken then replace
540 Transport :\tparameter error
Parameter error reported by the
transport controller. - Software error.
- Retry and continue.
- Restart the system.
- Report error to your service representative.
541 Transport :\tPower dip detected
A power dip was detected on the
power supply of the transport
controller. - Defective power supply. - Check power supply.
542
Transport :\temergency input
active
This error message is obsolete
and should not occur - Report error to your service representative.
543
Transport :\temergency output
active
This error message is obsolete
and should not occur - Report error to your service representative.
544 Transport :\tFlash PROM full
The flash PROM on the transport
controller board is full. - Purge flash PROM.
545
Transport :\tFlash PROM write
error
The flash PROM on the transport
controller board has one or more
locations which can not be written.
- The flash PROM is write protected.
- The flash PROM is defective.
- Put jumper X44 on the transport controller board.
- Exchange transport controller.
546
Transport :\tFlash prom erase
error
The flash PROM has one or more
location which can not be erased.
This is an error in the flash PROM on the transport controller
board. - Exchange transport controller.
547 Transport :\twrong flash ID Flash PROM is write protected.
- The flash prom on the controller is of the wrong type.
- No jumper X44 is installed on the controller card.
- Replace with correct type: 28F256 (Intel 89B9 or SGS 20AA).
- Install jumper X44 on the controller card.
548
Transport :\tUnexpected board at
run-in
The first sensor in the run-in
detects an unexpected board.
- Unexpected board at first sensor.
- Defective first sensor.
- Malfunction in sensor communication.
- Remove the board from the run-in.
- Check the first sensor of the run-in.
- Retry operation and continue, if not correct contact your service
representative.
549
Transport :\tUnexpected board in
run-in
An unexpected board was
detected at the second sensor of
the run-in.
- Unexpected board at second sensor in the run-in.
- Defective sensor (either first or second run-in sensor).
- Malfunction in sensor communication.
- Remove unexpected board from run-in.
- Check first and second sensor of the run-in.
- Retry operation and continue, if not correct contact your service
representative.
550
Transport :\tUnexpected board in
work-area
An unexpected board was
detected on the first sensor in the
work-area
- Unexpected board at first sensor in the work-area.
- Defective sensor (either first or second work-area sensor).
- Malfunction in sensor communication.
- Remove unexpected board from work-area.
- Check first and second sensor in work-area.
- Retry the operation and continue, if not correct contact your service
representative.
551
Transport :\tUnexpected board in
work-area
An unexpected board was
detected on the second sensor in
the work-area
- Unexpected board at second sensor in the work-area
- Defective sensor (either first or second work-area sensor).
- Malfunction in sensor communication.
- If none of above, possible reflection on the XY-robot.
- Remove unexpected board from the work-area.
- Check first and second sensor in the work-area.
- In case of reflection, decrease the sensitivity of that sensor sligthly. Be sure
the sensitivity is right to detect all kinds of boards, which have to be p
552
Transport :\tUnexpected board in
work-area
An unexpected board was
detected at the third sensor in the
work-area.
- Unexpected board detected in the work-area.
- Defective sensor (either second or third work-area sensor).
- Malfunction in sensor communication.
- Remove unexpected board from work-area.
- Check second and third sensor in work-area.
- Retry the operation and continue, if not correct contact your service
representative.
553
Transport :\tUnable to position
board in work area
The transport is not able to
position a board on the second
sensor in the work-area.
- Transport speed is too large.
- Acceleration is too low.
- Reduce board transfer speed.
- Enlarge the belt acceleration.
554
Transport :\tunexpected board in
run-out
The first sensor in the run-out
detects an unexpected board
- Unexpected board at first sensor.
- Defective first sensor.
- Malfunction in sensor communication.
- Remove unexpected board from run-out.
- Check the first sensor of the run-out.
- Retry operation and continue, if not correct contact your service
representative.
555
Transport :\tunexpected board in
run-out
An unexpected board was
detected at the second sensor in
the run-out.
- Unexpected board at second sensor in the run-out
- Defective sensor (either first or second run-out sensor).
- Malfunction in sensor communication.
- Remove unexpected board from the run-out.
- Check first and second sensor of the run-out.
- Retry the operation and continue, if not correct contact your service
representative.
556
Transport :\tMissing board in run-
in
The previous machine signaled
the arrival of a board. However,
the board was not detected within
the time frame
on the first sensor in the run-in
section.
- The board is stuck between the previous machine and the run-
in.
- Defective sensor (first run-in sensor).
- The first sensor is not correctly adjusted.
- Defective wiring I/O.
- Remove the stuck board.
- Adjust the transport width to match the board dimensions.
- Adjust the preceding machine so that it is correctly in line.
- Retry the action.
557
Transport :\tMissing board in run-
in
A board was detected at the first
sensor in the run-in. However, the
board was not detected within the
time frame
on the second sensor in the run-in
section.
- The board is stuck between the first and second sensor of the
run-in.
- Defective sensor (second run-in sensor).
- The second sensor is not correctly adjusted.
- Defective wiring I/O.
- Check width of the transport system, if necessary adjust the width.
- Retry the operation and continue.
- Check the second sensor in the run-in.
- Check wiring I/O.
- Check if sensor sesitivity is set to maximum.
558
Transport :\tMissing board in work-
area
A request was made to transport a
board from the run-in to work-
area. The transport was started,
however, the board was not
detected within the time frame on
the first sensor in the work-area
section.
- The board is stuck between the run-in and the first sensor of
the work-area.
- Defective sensor (first sensor of the work-area).
- The first sensor is not correctly adjusted.
- Defective wiring I/O.
- Check the width of the transport system, if necessary adjust the width.
- Retry the operation and continue.
- Check the first sensor in the work-area.
- Check wiring I/O.
- Check sensor adjustment.
559
Transport :\tMissing board in work-
area
A board was detected at the first
sensor in the work-area. However,
the board was not detected within
the time frame
on the second sensor in the work-
area section. Or the transport was
not able to transport the board out
of the work-area.
- The board is stuck between the first and second sensor of the
work-area.
- Defective sensor (second sensor in the work-area).
- The second sensor is not correctly adjusted.
- Defective wiring I/O.
- Check the width of the transport system, if necessary adjust the width.
- Retry the operation and continue.
- Check the second sensor in the work-area.
- Check wiring I/O.
- Check sensor adjustment.
560
Transport :\tMissing board in work-
area
A board was detected at the
second sensor in the work-area.
However, the board was not
detected within the time frame
on the third sensor in the work-
area section. Or the transport was
not able to transport the board out
of the work-area.
- The board is stuck between the second and third sensor of
the work-area.
- Defective sensor (third sensor in work-area).
- The third sensor is not correctly adjusted.
- Defective wiring I/O.
- Check the width of the transport system, if necessary adjust the width.
- Retry the operation and continue.
- Check the third sensor in the work-area.
- Check wiring I/O.
- Check sensor adjustment.
561
Transport :\ttime-out occurred on
board move
This message is obsolete and
should not occur. - Report error to your service representative.