1OM-1625-004_w.pdf - 第139页

1OM-1603 3-16 2. Program Change Operation : Chap.3 1012-001 2.2.5 Replacement of Bank Feeder Change Cart CAUTION Do not put your hand in the moving area while the feeder base is moving up or down. While the LED of the Fe…

100%1 / 219
1OM-1603
3-15
2. Program Change Operation : Chap.3
1012-004
(4) Attach the bank feeder change cart to the machine.
Reference
(a) Refer to "Attachment and Detachment of Tape Feeders" in the
instruction manual of the tape feeders for how to install the tape
feeders on the bank feeder change cart.
(b) Refer to "3.8 Cart Installation Section" in "Chapter 1" for how to
attach the bank feeder change cart.
CAUTION
Hazardoustoyourhandsandngers!
•
Be sure to hold the handle to move the bank feeder
change cart.
Watch
yourstep!
•
Be careful not to hit your foot against the cart while
moving the bank feeder change cart.
Especially, the resistance against cart movement may
change rapidly when the oor is ragged and the cart
gets caught on the oor or a sheet is used and the cart
gets caught at the edge or a slackened portion of the
sheet.
•
Make sure to insert the feeder into the deep end.
When the tape feeder is mounted onto the feeder
carriage, make sure that it has been inserted into the
deep end and xed securely.
In the case that it has not been xed securely, the tape
feeder might fall, which might cause a lower leg injury
or damage to the feeder..
Feeder Workbench
Bank Feeder Change Cart
Feeder Base
F1C13
1OM-1603
3-16
2. Program Change Operation : Chap.3
1012-001
2.2.5 Replacement of Bank Feeder Change Cart
CAUTION
Do not put your hand in the moving area while the
feeder base is moving up or down.
While the LED of the Feeder Ready switches are being
ickering, it indicates that the corresponding feeder base
is moving up and down.
Procedure
(1) Press the Feeder Ready switches of the machine.
(The feeder READY switch LED will be extinguishes and the feeder base is
unclamped.)
(2) Keep pressing the Feeder Ready switches of the machine a little longer.
(The feeder base starts moving down and the LED of the Feeder Ready
switches starts ickering, indicating that the feeder base is being activated.)
When the disconnection operation of the bank feeder change cart is
completed, the LED of the Feeder Ready switches extinguishes.
(3) Detach the connector xing lever and pull out the connector for the bank
feeder change cart from the connector to the machine. Then, catch the
connector on the magic tape section on the side of the cart.
Notice
(a) Do not use the connector catching section for any purpose
otherthanforcatchingthespeciedsectionoftheconnector.
Also, do not put any excessive force on it. Doing so might
damage the connector.
(b) During the machine operation, do not disconnect the connector.
For the feeder base connector, connect or disconnect it when
the feeder base is lowered to the end and it has stopped.
(4) Release the two stopper brakes of the bank feeder change cart and draw out
the cart from the machine.
(5) Insert the bank feeder change cart (provided with the tape feeders set ready
for use) into the machine and lock the two stopper brakes.
Notice
(a) When the bank feeder change cart must be pushed into the
machine, push it straight such that the guide on the machine
side can be located inside the cart arm.
Also, insert it taking care that your hand holding the cart handle
does not hit the cover.
(b) When the cart is not positioned correctly, the connection
operation cannot be performed.
Besuretopushthecart
rmlyuntilittouchesthestopper.
1OM-1603
3-17
2. Program Change Operation : Chap.3
1012-001
(6) Connect the connector of the cart to the connector on the machine side and
set the connector xing lever in place.
Notice
When the bank feeder change cart must be pushed into the
machine, push it straight such that the guide on the machine side
can be located inside the cart arm.
(7) Press the Feeder Ready switches of the machine.
(The feeder base starts moving up and the LED of the Feeder Ready switches
starts ickering, indicating that the feeder base is being activated.)
(8) Press the Feeder Ready switches of the machine.
The feeder READY switch LED is turned ON and the feeder base is
clamped.