Siplace TX-设备参数-EN.pdf - 第11页
11 Placement heads SIPLACE TwinStar (TH) SIPLACE TwinStar (TH) with component camera type 33 (fine pitch camera) with component camera type 25 (flip chip camera ) Component range a a) Please note that the placeable comp …
10
Placement heads
SIPLACE MultiStar (CPP)
SIPLACE MultiStar (CPP)
with component camera
type 30
With component camera
type 45
with component camera
type 33
(stationary camera)
Component range
a
a) Please note that the placeable component range is also affected by the pad geometry, the customer-specific stan-
dards, the component packaging tolerances and the component tolerances.
01005 to 27 mm x 27 mm 01005 to 15 mm x 15 mm 0402 to 50 mm x 40 mm
b
b) A diagonal of 69 mm is possible during multiple measurements (e.g. 64 mm x 10 mm).
Component spec.
Max height
c
Max. height
d
Min. lead pitch
Min. lead width
Min. ball pitch
Min. ball diameter
Min. dimensions
Max. dimensions
Max. weight
c) CPP head: in low installation position (stationary component camera not possible).
d) CPP head: in high installation position
6.0 mm
8.5 mm
0.25 mm
0.10 mm
e
/ 0.2 mm
f
0.25 mm
e
/ 0.35 mm
f
0.14 mm
e
/ 0.20 mm
f
0.4 mm x 0.2 mm
27 mm x 27 mm
4 g
e) For components < 18 mm x 18 mm
f) For components ≥ 18 mm x18 mm
6.0 mm
8.5 mm
0.25 mm / 0.12 mm
g
0.05 mm
0.14 mm
0.07 mm
0.11 mm x 0.11 mm
15 mm x 15 mm
4 g
g) Only possible for components which are within the camera focal area of ± 1.3 mm.
11.5 mm
0.3 mm
0.15 mm
0.35 mm
0.2 mm
1.0mm x 0.5mm
50 mm x 40 mm
8 g
Programmable set-down
force
1.0 - 10 N 1.0 - 10 N 1.0 - 10 N
Nozzle types 20xx, 28xx 20xx, 28xx 20xx, 28xx
X/Y accuracy
h
h) The accuracy values are measured during the machine acceptance tests. They correspond to the conditions set
out in the ASM scope of service and supply.
± 40 µm/3σ ± 40 µm/3σ ± 34 µm/3σ
Angular accuracy ± 0.20° / 3σ
i
, ± 0.38° / 3σ
j
i) Component dimensions between 6 mm x 6 mm and 27 mm x 27 mm.
j) Component dimensions smaller than 6 mm x 6 mm.
± 0.18° / 3σ ± 0.14° / 3σ
Illumination level 5 5 6
Standard functions High-resolution camera, vacuum sensor, force measurement, component sensor,
integrated turning station per segment, PCB warpage check, individual image of
each component
11
Placement heads
SIPLACE TwinStar (TH)
SIPLACE TwinStar (TH)
with component camera type 33
(fine pitch camera)
with component camera type 25
(flip chip camera)
Component range
a
a) Please note that the placeable component range is also affected by the pad geometry, the customer-specific standards, the
component packaging tolerances and the component tolerances.
0402 to SO, PLCC, QFP, BGA, special
components, bare dies, flip-chips
0201 to SO, PLCC, QFP, sockets,
plugs, BGA, special components, bare
dies, flip-chips, shields
Component specs
Max. height
Min. lead pitch
Min. lead width
Min. ball pitch
Min. ball diameter
Min. dimensions
Max. dimensions
Max. weight
b
b) Component plus nozzle or gripper.
25 mm
0.3 mm
0.15 mm
0.35 mm
0.2 mm
1.0mm x 0.5mm
55 mm x 45 mm (single measurement)
up to
200 mm x 125 mm (multiple measurement)
c
100 g
c) Further restrictions considered in SIPLACE Pro apply depending on component dimensions and component supply.
25 mm
0.25 mm
0.1 mm
0.14 mm
0.08 mm
0.6 mm x 0.3 mm
16 mm x 16 mm (single measurement)
100 g
Programmable set-down
force
1.0 N - 15 N 1.0 N - 15 N
Nozzle types 5xx (standard)
20xx/28xx + adapter
4xx + adapter
9xx + adapter
Gripper
5xx (standard)
20xx/28xx + adapter
4xx + adapter
9xx + adapter
Gripper
Nozzle spacing for P&P
heads
70.8 mm 70.8 mm
X/Y accuracy
d
d) The accuracy values are measured during the machine acceptance tests. They correspond to the conditions set out in the
ASM scope of service and supply.
± 28 µm/3σ ± 22 µm/3σ
Angular accuracy ± 0.05° / 3σ ± 0.05° / 3σ
Illumination level 6 6
Standard functions Stationary fine pitch camera, vacuum sensor, force measurement, nozzle changer,
PCB warpage check, individual image of each component
12
Placement heads
Nozzle changer
Nozzle changer for the SIPLACE SpeedStar (C&P20 P)
Nozzle changer for the SIPLACE MultiStar CPP
Nozzle changer for the SIPLACE TwinStar
Magazine for 20 nozzles of type
40xx
Magazine for 9 nozzles of
type 28xx
Magazine for 20 nozzles of type 20xx
Magazine for two standard nozzles
Magazine for one special nozzle, gripper
Description
Nozzle changers increase the flexibility of the placement heads when it comes to processing
different components. The nozzle configuration can be rapidly adjusted to changing place-
ment jobs. Precisely defined positions and perfect nozzle seat in the garage ensure minimum
radial eccentricity on the placement head.
The nozzle changers feature a monitoring circuit. This checks whether the nozzle magazines
are seated correctly on the mount. In addition, the nozzle changer recognizes whether the
magazines are for 40xx, 20xx or 28xx nozzles by the code.