00196602-05_SM_SIPLACE_X-Feeder_EN.pdf - 第62页
6 Repairing the X Feeder modules 6.5 Foil Disposal 62 Service Manual SIPLACE X-Feeder 4 - 88 mm 11/2017 ► Fix the cable with the rubber seal (1) . Make sure that the rubber seal does not project beyond the holder. ► Make…
6 Repairing the X Feeder modules
6.5 Foil Disposal
Service Manual SIPLACE X-Feeder 4 - 88 mm 11/2017 61
► Remove the rubber seal marked in the diagram
(1).
► Loosen the screws marked in the diagram (2).
► Lift the cover plate off the foil disposal drive.
Example diagram of 16mm feeder module
► Loosen the two screws marked in the diagram.
► Carefully pull the ratchet to the left, away from
the foil disposal drive.
► Remove the cable from the opening in the
ratchet.
The ratchet is now free.
6.5.5.4 Fitting the Ratchet (16 - 88 mm)
Example diagram of 16mm feeder module
► Insert the connector through the opening in the
ratchet.
► Push the ratchet sideways under the small board,
as far as the foil disposal drive.
► Fix the ratchet first with the top cylinder head
screw (2.5x10mm).
Do not tighten the screw fully as you still need to
move the ratchet slightly.
► Fix the ratchet into place with the bottom cylinder
head screw (2.5x10mm).
► Now tighten the top screw.
► Run the cable as marked in the diagram.
6 Repairing the X Feeder modules
6.5 Foil Disposal
62 Service Manual SIPLACE X-Feeder 4 - 88 mm 11/2017
► Fix the cable with the rubber seal (1).
Make sure that the rubber seal does not project
beyond the holder.
► Make sure that the corresponding washers are
on the toothed wheel axes (2).
► Place the cover plate onto the foil disposal drive.
Make sure that the cover plate on the toothed
wheel axes (1) engages and lies level on the foil
disposal drive.
► Fix the cover plate with the countersunk screws
marked in the diagram (M2.5 x 5mm).
For 16mm feeder modules only
► Turn the foil disposal drive over, together with the
foil container.
► Fasten the mushroom head cutting screw (Torx)
marked in the diagram.
► Turn the foil disposal drive over again.
Example diagram of 16mm feeder module
► Place the rubber seal into the fixture as marked
in the diagram.
On the left-hand side, this rubber seal should be
flush while on the right-hand side it should project
somewhat. The spacer will then be fitted to this
projected part of the rubber seal.
6 Repairing the X Feeder modules
6.5 Foil Disposal
Service Manual SIPLACE X-Feeder 4 - 88 mm 11/2017 63
► Insert the foil disposal drive, together with the foil
container, into the feeder module.
► (1) Insert the flat ribbon cable into the connection,
as far as the stop.
Make sure that the blue surface at the end of the
cable is at the top and that the flat ribbon cable
lies straight in the connection.
► Swing the lock on the connection down onto the
flat ribbon cable.
Make sure that the flat ribbon cable is fitted firmly
in the connection. Tug gently on the cable to
check.
► Check again whether the flat ribbon cable is fitted
straight in the connection.
If necessary, open the lock and correct the posi-
tion of the cable before closing the lock again.
► (2) and (3)
Carefully insert the connector in the direction of
the arrow, as far as the stop, into the connection
shown.
Make sure that the smooth side of the connector
is at the top.
CAUTION!
Do not push the connector with force into the
connection, otherwise individual pins may
break off or be distorted.
.
► (4) Insert the other connector into the connection
marked in the diagram.
► Push the spacer from the right in the direction of
the arrow, around the rubber seal.
► Fix the spacer with the screws marked in the dia-
gram.
Note: screw (1) only used for 16mm feeder mod-
ules.
(1) Cylinder head Phillips screw with washer
(2) Mushroom head cutting screw (Torx long)
(3) Countersunk cutting screw (Torx short)
► Fit the left side cover into place (see 6.3.2 "Fitting
the Left Side Cover" [}24]).