00196602-05_SM_SIPLACE_X-Feeder_EN.pdf - 第68页
6 Repairing the X Feeder modules 6.6 Rocker 68 Service Manual SIPLACE X-Feeder 4 - 88 mm 11/2017 6.6.1.2 Fitting the Rocker Stripping Device ► Place the stripping device on the side of the rocker as indicated. Make sure …
6 Repairing the X Feeder modules
6.6 Rocker
Service Manual SIPLACE X-Feeder 4 - 88 mm 11/2017 67
6.6 Rocker
6.6.1 Rocker Stripping Device (4mm only)
Required spare parts
Rocker Stripping Device
Feeder module Item no. Designation
4 mm 03087913-Sxx Stripping device /rocker X4
Required tools
●
Flat bladed (slotted) screwdriver
6.6.1.1 Removing the Rocker Stripping Device
► Remove the rocker (see 6.6.2.1 "Removing the
Rocker (4 - 88 mm)" [}69]).
► Loosen the screw that fixes the stripping device
at the top of the rocker.
► Loosen the screw that fixes the stripping device
at the bottom of the rocker.
► Pull the stripping device sideways from the
rocker.
6 Repairing the X Feeder modules
6.6 Rocker
68 Service Manual SIPLACE X-Feeder 4 - 88 mm 11/2017
6.6.1.2 Fitting the Rocker Stripping Device
► Place the stripping device on the side of the
rocker as indicated.
Make sure that the longer bracket is on top.
► Align the stripping device straightly and screw it
to the rocker at the top and bottom.
► Fasten the rocker (see 6.6.2.2 "Fitting the Rocker
(4 - 88 mm)" [}70]).
6.6.2 Rocker Assembly
Required spare parts
Example: rocker 8mm (left), rocker 24mm (right)
6 Repairing the X Feeder modules
6.6 Rocker
Service Manual SIPLACE X-Feeder 4 - 88 mm 11/2017 69
Feeder
module
Item no. Module
Version <= -06
Item no. Module
with upgrade kit
Item no. Module
Version >= -07
Designation
4 mm 03087914-xx 03087914-xx 03087914-xx Rocker assembly, /X4
8 mm 03042320-xx 03042320-xx 03042320-xx Rocker assembly, /X8
12 mm 03042350-xx 03042350-xx 03042350-xx Rocker assembly, /X12
16 mm 03042354-xx 03097025-xx
03117039-xx
03097025-xx Rocker assembly, /X16
24 mm 03041968-xx 03085748-xx
03117040-xx
03085748-xx Rocker assembly, /X24
32 mm 03042445-xx 03085757-xx
03117041-xx
03085757-xx Rocker assembly, /X32
44 mm 03042485-xx 03085142-xx
03117043-xx
03085142-xx Rocker assembly, /X44
56 mm 03043388-xx 03085767-xx
03117044-xx
03085767-xx Rocker assembly, /X56
72 mm 03043400-xx 03085777-xx
03117045-xx
03085777-xx Rocker assembly, /X72
88 mm 03042228-xx 03085786-xx
03117046-xx
03085786-xx Rocker assembly, /X88
Modules with upgrade kit:
Feeder modules which contain an upgrade kit (marked with the
label below), can have the module version -07 rocker fitted as a
spare part (item no.).
When replacing this assembly, you must also replace the tamp
wheel on the drive side opposite with a module -07 version.
Required tools
●
Flat bladed (slotted) screwdriver
●
Split pin punch size 1.4
6.6.2.1 Removing the Rocker (4 - 88 mm)
► Carefully place the feeder module down on its left
side.
► Press the rocker as far as the left stop, into the
spring, to relieve the bearing shaft. If tension is
not taken off the bearing shaft, the shaft thread
could be damaged during loosening.
► Loosen the bearing shaft marked in the diagram.
The shaft thread ends after several millimeters.
► Stand the feeder module up.
► Press the bearing shaft sideways out of the
rocker, with a split pin punch.
► Slowly release the rocker.
You can now remove the rocker.